DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 14, Problem 1RQ
What are some of the factors that influence the selection of a specific casting process as a means of making a product?
Expert Solution & Answer
To determine
Factors that influence the selection of a specific casting process to make a product.
Explanation of Solution
There are a number of the metal casting processes are available in the market. Each process has its characteristics, advantages, and benefits. The selection of the best process as a means of making products is too difficult and requires a good understanding of products and in the process. some factors must be considered while selecting a casting process, which is given below −
- Dimensional tolerance
- Surface finish
- Number of casting
- Types of pattern and core box
- Economics of the casting process
- Types of metal
- Size of the product
- Strength of the product
If the requirement of products is too large, then we can choose permanent mold casting. Further, we have different types of casting availability, which can be selected through our requirements and understanding.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A 3-in.-radius drum is rigidly attached to a 5-in.-radius drum as shown. One of the drums rolls without sliding on the surface shown, and a cord is wound around the other drum. Knowing that at the instant shown. point A has a velocity of 4.875 in./sin./s and an acceleration of 15.50 in./s2in./s2 , both directed to the right, determine the accelerations of points A, B, and C of the drums.
The cord is wound around the 3 inch radius drum. Point B is at the bottom of the 5 inch radius drum. Point A is at the bottom of the 3 inch radius drum. Point C is on the right edge of the 5 inch radius drum.
The accelerations of point B is______ in./s2 .
The accelerations of point A is ______ in./s2 ______ ⦨ °. at what angle/direction
The accelerations of point C is______ in./s2 ______ ⦪ °. at what angle/direction?
A total volume of mud is 1,000 bbls that has a mud weight of 9.1 ppg. Calculate the volumefractions of water, Bentonite, and the weight of Bentonite used. Density of powder Bentonite is 156 lbm/ft3
A 3-in.-radius drum is rigidly attached to a 5-in.-radius drum as shown. One of the drums rolls without sliding on the surface shown, and a cord is wound around the other drum. Knowing that at the instant shown. point A has a velocity of 4.875 in./sin./s and an acceleration of 15.50 in./s2in./s2 , both directed to the right, determine the accelerations of points A, B, and C of the drums.
The cord is wound around the 3 inch radius drum. Point B is at the bottom of the 5 inch radius drum. Point A is at the bottom of the 3 inch radius drum. Point C is on the right edge of the 5 inch radius drum.
The accelerations of point B is ______ in./s2
The accelerations of point A is ______ in./s2 _____⦨ °.
The accelerations of point C is _______ in./s2 ____ ⦪ °.
Chapter 14 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 14 - What are some of the factors that influence the...Ch. 14 - What are the three basic categories of casting...Ch. 14 - What metals are frequently cast into products?Ch. 14 - What features combine to make cast iron and...Ch. 14 - Which type of casting is the most common and most...Ch. 14 - Prob. 6RQCh. 14 - Prob. 7RQCh. 14 - What is the simplest and least expensive type of...Ch. 14 - What is a match plate, and how does it aid...Ch. 14 - How is a cope-and-drag pattern different from a...
Ch. 14 - Prob. 11RQCh. 14 - Prob. 12RQCh. 14 - For what types of products might a loose-piece...Ch. 14 - What are the four primary requirements of molding...Ch. 14 - Prob. 15RQCh. 14 - Prob. 16RQCh. 14 - What is a muller, and what function does it...Ch. 14 - Prob. 18RQCh. 14 - What is a standard rammed specimen for evaluating...Ch. 14 - What is permeability, and why is it important in...Ch. 14 - How does the ratio of water to clay affect the...Ch. 14 - How is the hardness of molding sand determined?Ch. 14 - Prob. 23RQCh. 14 - How does the size and shape of the sand grains...Ch. 14 - Prob. 25RQCh. 14 - Prob. 26RQCh. 14 - Prob. 27RQCh. 14 - Prob. 28RQCh. 14 - Prob. 29RQCh. 14 - Prob. 30RQCh. 14 - What are hot tears, and what can cause them to...Ch. 14 - When might hand ramming be the preferred method of...Ch. 14 - Prob. 33RQCh. 14 - Prob. 34RQCh. 14 - Prob. 35RQCh. 14 - Prob. 36RQCh. 14 - What is stack molding?Ch. 14 - Prob. 38RQCh. 14 - What are the components of green sand?Ch. 14 - Prob. 40RQCh. 14 - Prob. 41RQCh. 14 - Prob. 42RQCh. 14 - What are some of the advantages and limitations of...Ch. 14 - Prob. 44RQCh. 14 - Prob. 45RQCh. 14 - Prob. 46RQCh. 14 - Prob. 47RQCh. 14 - Prob. 48RQCh. 14 - Prob. 49RQCh. 14 - Why do shell molds have excellent permeability and...Ch. 14 - Prob. 51RQCh. 14 - Prob. 52RQCh. 14 - Prob. 53RQCh. 14 - Prob. 54RQCh. 14 - Prob. 55RQCh. 14 - What is the sand binder in the core-oil process,...Ch. 14 - What is the binder in the hot-box core-making...Ch. 14 - What is the primary attraction of the cold-box...Ch. 14 - What is shelf life? How is it different from bench...Ch. 14 - Prob. 60RQCh. 14 - Prob. 61RQCh. 14 - Prob. 62RQCh. 14 - Prob. 63RQCh. 14 - Prob. 64RQCh. 14 - Prob. 65RQCh. 14 - Why are plaster molds only suitable for the...Ch. 14 - How does the Antioch process provide permeability...Ch. 14 - What is the primary performance difference between...Ch. 14 - Prob. 69RQCh. 14 - Prob. 70RQCh. 14 - Prob. 71RQCh. 14 - Describe the progressive construction of an...Ch. 14 - Why are investment casting molds generally...Ch. 14 - Prob. 74RQCh. 14 - What are some of the attractive features of...Ch. 14 - What recent development has made one-of-a-kind or...Ch. 14 - Prob. 77RQCh. 14 - Prob. 78RQCh. 14 - What are some of the benefits of not having to...Ch. 14 - What are some of the ways by which expanded...Ch. 14 - Prob. 81RQCh. 14 - Prob. 82RQCh. 14 - Prob. 83RQCh. 14 - Prob. 84RQCh. 14 - Prob. 85RQCh. 14 - Prob. 86RQCh. 14 - What are the most common single-use mold...Ch. 14 - What are the most common methods of core...Ch. 14 - Although cores increase the cost of castings, they...Ch. 14 - Several of the additive manufacturing processes...Ch. 14 - Additive manufacturing processes can also build...Ch. 14 - Figure CS-14 shows the hitch ball component of a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The average heat transfer coefficent for airflow over an odd shaped body is to be determined by mass transfer measurements and using the Chilton-Colburn analogy btwn heat and mass transfer. The experiemnt is conducted by blowing dry air at 1 atm at a free-stream velocity of 2 m/s over a body covered with a layer of naphthalene. The surface area of the body is .75 m^2, and it is observed that 100 g of maphthalene has sublimated in 45 min. During the experiemnt, both the body and the air were kep at 25oC, at which the vapor pressure and mass diffusivity of naphthalene are 11 Pa and Dab=0.61*10^-5 m^2/s respectively. Determine the heat transfer coefficent under the same flow conditions over the same geometry.arrow_forwardAuto Controls Design a PID controller for thefollowing system so that the modified system satisfies the followingspecifications : 1. settling time ,ts = 1.96 s and % Overshoot Mp = 70.7 % Assume a non-dominant pole at s = -15 to solve the problem The plot the compensated andThen plot the uncompensated system in MATLAB. what can you see from the plot ? what is your observation ?arrow_forwardAuto Controls The figure is a schematic diagram of an aircraft elevator control system. The input to the systemin the deflection angle of the control lever , and the output is the elevator angle phi.show that for each angle theta of the control lever ,there is a corresponding elevator angle phi. Then find Y(s)/theta(s) and simplify the resulting transfer function . Also note from the diagram that y and phi is relatedarrow_forward
- Fresh water is planned to be pumped in a certain pipe at constant pumping rate of 6.5 gpm. If water density and viscosity are 8.34 ppg and 1.0 cp, what is the minimum pipe inside diameter that make the fluid flow behave as turbulent flow?arrow_forwardUSE MATLAB ONLY provide typed code Turbomachienery . GIven: vx = 185 m/s, flow angle = 60 degrees, R = 0.5, U = 150 m/s, b2 = -a3, a2 = -b3 Find: velocity triangle , a. magnitude of abs vel leaving rotor (m/s) b. flow absolute angles (a1, a2, a3) 3. flow rel angles (b2, b3) d. specific work done e. use code to draw vel. diagram Use this code for plot % plots Velocity Tri. in Ch4 function plotveltri(al1,al2,al3,b2,b3) S1L = [0 1]; V1x = [0 0]; V1s = [0 1*tand(al3)]; S2L = [2 3]; V2x = [0 0]; V2s = [0 1*tand(al2)]; W2s = [0 1*tand(b2)]; U2x = [3 3]; U2y = [1*tand(b2) 1*tand(al2)]; S3L = [4 5]; V3x = [0 0]; V3r = [0 1*tand(al3)]; W3r = [0 1*tand(b3)]; U3x = [5 5]; U3y = [1*tand(b3) 1*tand(al3)]; plot(S1L,V1x,'k',S1L,V1s,'r',... S2L,V2x,'k',S2L,V2s,'r',S2L,W2s,'b',U2x,U2y,'g',... S3L,V3x,'k',S3L,V3r,'r',S3L,W3r,'b',U3x,U3y,'g',...... 'LineWidth',2,'MarkerSize',10),... axis([-1 6 -4 4]), ... title('Velocity Triangle'), ... xlabel('x'),ylarrow_forwardConsider a 12 cm internal diameter, 14 m long circular duct whose interior surface is wet. The duct is to be dried by forcing dry air at 1 atm and 15oC throught it at an average velocity of 3m/s. The duct passes through a chilled roo, and it remains at an average temp of 15oC at all time. Determine the mass transfer coeeficient in the duct.arrow_forward
- Consider a 5m by 5m wet concret patio with an average water film thickness of .2mm. Now wind at 50 km/h is blowing over the surface. If the air is at 1 atm, 15oC and 35 percent relative humidity, determine how long it will take for the patio to completely dry.arrow_forwardA double thread worm gear has a pitch of 1 1/8 and a pitch diameter of 3 in. It has a coefficient of friction of 0.20 and normal angle (pressure angle) of 14.5o. The worm is supplied by 12 hp at 1200 rpm motor. Find the tangential force on the gear. The worm is left hand threads.arrow_forwardA double thread worm gear has a pitch of 1 1/8 and a pitch diameter of 3 in. It has a coefficient of friction of 0.20 and normal angle (pressure angle) of 14.5o. The worm is supplied by 12 hp at 1200 rpm motor. Find the tangential force on the gear. The worm is left hand threads.arrow_forward
- A 2 mm thick, 5L vessel made of nickel is used ot store hydrogen gas at 358 K and 300 kPa. If the total inner surface area of the vessel is 1600 cm^2, determine the rate of gas loss from the nickel vessel via mas diffusion. Also, determine the fraction of the hydrogen lost by mass diffusion after one year of storage.arrow_forward< 7:19 The 1st homework 6. Multiple Choice a)唧筒机构 5G31 Which of followings can be th e kinematic diagram of this mechanism? A B Darrow_forward2:54 The 1st homework . 5G 27 b)回转柱塞泵机构 Which of followings can be the kinematic diagram of this mechanis m? A B D Carrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Casting Metal: the Basics; Author: Casting the Future;https://www.youtube.com/watch?v=2CIcvB72dmk;License: Standard youtube license