The following data were collected from a manufacturing process involving reactor temperature measured in degrees Celsius. The following values are desired: average = 100 degrees Celsius; standard deviation = ±5 degrees Celsius.
Graph the data on a control chart. A blank god has been provided online; you may use this god or use graph paper as directed by your instructor. Be sure to clearly indicate the zones of control
Using the eight SPC rules, determine whether the process is in statistical control. If it is not 10 statistical control, indicate which rule or rules are violated and list the part numbers that violate those rules
Want to see the full answer?
Check out a sample textbook solutionChapter 14 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Additional Engineering Textbook Solutions
Mechanics of Materials
DESIGN OF MACHINERY
Thermodynamics: An Engineering Approach
Introduction To Finite Element Analysis And Design
HEAT+MASS TRANSFER:FUND.+APPL.
Applied Fluid Mechanics (7th Edition)
- In a study analyzed by the Statistics Consulting Center at Mutah University, a group of subjects was asked to complete a certain task on the computer. The response measured was the time to completion. The purpose of the experiment was to test a set of facilitation tools developed by the Department of Computer Science at the university. There were 10 subjects involved. With a random assignment, five were given a standard procedure using Fortran language for completion of the task. The other five were asked to do the task with the use of the facilitation tools. The data on the completion times for the task are given here. Group 1 Group 2 (Standard Procedure) (Facilitation Tool) 161 169 174 158 163 132 162 134 138 133 Assuming that the population distributions are normal and variances are the same for the two groups, support or refute the conjecture that the facilitation tools increase the speed with which the task can be accomplished.arrow_forwardPlease answer it correctly. Show solution step by step with Units. Thermodynamics... Topic: Work and Heatarrow_forwardDon't Use Chat GPT Will Upvote And Give Handwritten Solution Pleasearrow_forward
- Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…arrow_forwardAnswer the following question and explainarrow_forwardplease show work answer is Darrow_forward
- Record the dimensions of the known (calibration) block using the caliper and dial gauge on the table below. Indicate the units of each measurement. Calculate the average length of each side of the block. Dimension Caliper (Units) 0.995 1.455 0.985 Ruler(in) A: 0.9 B: 1.5 C: 0.9 A B C Dimension A B Instrument Use the average dimensions (see Problem 2a) of the known block to calibrate the LVDT at your workstation. Record the voltage on the table below: LVDT Offset: 0.556 (Do not include the offset value in your average dimensions) C Ave Dimension (Units) (Dial Gauge) 0.997 1.659 0.949 0.964 in 1.538 in 0.945 in oltage Average Dimension 1.244 volt 1.994 1.28 0.964 in 1.538 in 0.945 inarrow_forwardA certain system contains three branches in parallel. One branch contains units A and B in series. A second branch contains units C and D in series. The third branch contains unit E alone. These non-identical units have constant hazard rates in order of their unit number of 0.1/year, 0.15/year, 0.2/year, 0.15/year, and 0.25/year. a) Draw a block diagram and compute the reliability of the system from the reliabilities of the individual units. b) Draw a signal flow graph. c) Identify the cut sets and the minimal cut sets. d) Find reliability of the system. e) Find the mean time to failurearrow_forwardThe number line below shows a value on a log scale. 10-5 10 103 102 10-1 100 101 10² 103 104 105 What is, approximately, the value of the point shown on the number line? x = Question Help: D Video D Post to forum Submit Question arch 米 11 144 14 24 41 %23 & 3 T Y K 01 96 近 R EIarrow_forward
- Make the graphs shown on the picture exactly the same. Follow the directions in the other picture. Please make the graphs look exactly the same as the picture. Make them on MATLAB, please send code.arrow_forwardAs an exercise, a student weighed several bunches of nails on a balance. The nails were not all the same size. Here are the student's data: 4. number of nails mass in grams 82 122 208 324 435 12 20 26 Prepare a plot of these data on the grid below or on the graph paper. Use "number of nails" as the independent variable and be certain to scale and label the axes correctly. Scale the axes starting at the origin; 0, 0. GO 20 向 12 円 Number of nails Cx) 2. 18 20 mass inarrow_forwarddocuments from ICloOud. QUESTION 16 An interval recorded 9 occurrences. What is the 93% upper confidence limit(one-sided) for the number of occurrences in an interval? Please use at least 2 decimal points for your answer.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY