Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 13, Problem 6MC
Which of the following statements about preparing to assemble an engine is not true?
- Discard and replace all bolts that are damaged.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
If the service information does not provide a loosening sequence for the cylinder head bolts, what should you do?
Please send Complete answer for getting upvote
Detailed answer
what is Flyweight Design Pattern
Application
Real world example
Pros and cons
What type of caps are used to hold the crankshaft in place once it’s installed in the block?
Chapter 13 Solutions
Automotive Technology
Ch. 13 - What are the major differences between aerobic and...Ch. 13 - How does a torque-to-yield bolt differ from...Ch. 13 - How do seals differ from gaskets?Ch. 13 - Where are thread sealers most often used?Ch. 13 - On hybrid vehicles, how can you identify the high...Ch. 13 - True or False? Make sure you locate and adhere to...Ch. 13 - True or False? The computer in most late-model...Ch. 13 - True or False? Some crankshaft and camshaft timing...Ch. 13 - True or False? Valve lash is adjusted in many...Ch. 13 - Which of the following statements is incorrect?...
Ch. 13 - Which of the following statements about the...Ch. 13 - Graphite is. an anaerobic substance an RTV an...Ch. 13 - Which of the following are considered soft, cut...Ch. 13 - What material is typically not used to form a rear...Ch. 13 - Which of the following statements about preparing...Ch. 13 - Prob. 1ASRQCh. 13 - Technician A uses adhesives to hold gaskets in...Ch. 13 - Technician A uses soft gaskets on valve covers....Ch. 13 - While installing a timing belt: Technician A...Ch. 13 - Technician A says that oil pan gaskets are often...Ch. 13 - Prob. 6ASRQCh. 13 - While discussing proper engine break-in:...Ch. 13 - Prob. 8ASRQCh. 13 - Prob. 9ASRQCh. 13 - While selecting the proper RTV for a particular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following statements is incorrect? Cylinder head bolts must be tightened to the proper amount of torque. Most cylinder head bolts are tightened in a sequence that starts on one end. On some engines, the head bolts are retorqued after the engine has been run and is hot. Many engines use head bolts of different lengths.arrow_forwardWhy is it important to loosen the cylinder head bolts in the recommended order?arrow_forwardWhat other engine components may have to be used to be machined if the cylinder heads are machined on a v-type engine ?arrow_forward
- can you show a clear sloutionarrow_forwardWhich of the following is not of concern when checking a piston? Diameter Surface finish Groove wear Pin boss wobblearrow_forwardWhen removing the piston and rod assemblies from a cylinder block; Technician A positions the throw of the crankshaft at the top of its stroke and removes the connecting rod nuts and cap. Technician B covers the rod bolts with protectors and pushes the piston and rod assembly out with the wooden hammer handle or wooden drift and supports the piston as it comes out of the cylinder. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- What should be done to remove rust, corrosion, pitting, and scratches from the piston bore?arrow_forwardWhile servicing a pair of aluminum cylinder heads: Technician A says it' needed, both heads must be machined equally and the same amount of material removed from each. Technician B replaces both heads if the warpage exceeds the specified allowable amount Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY