Concept explainers
(a)
The dimension for the circular channel.

Answer to Problem 50P
The diameter of the circular channel is
The depth of the circular channel is
Explanation of Solution
Given Information:
The water flow rate is
Write the expression for the volume flow rate of the water.
Here, the manning coefficient is
Write the expression for the radius of the semicircle.
Here, the diameter of the semicircle is
Write the expression for the area of the circular channel.
Here, the diameter of the circle is
Write the expression for the perimeter of the circular channel.
Substitute
Write the expression for the flow depth of the circular channel.
Calculation:
Refer to table 13-1 "Mean values of the manning coefficient
Substitute
Substitute
Conclusion:
The diameter of the circular channel is
The depth of the circular channel is
(b)
The dimension for the rectangular channel.

Answer to Problem 50P
The dimension for the rectangular channel are-
The bottom breadth of the rectangular channel is
The depth of the rectangular channel is
Explanation of Solution
Given Information:
The water flow rate is
Write the expression for the area of the rectangular channel.
Here, the depth of the rectangular is
Write the expression for the flow depth of the rectangular channel.
Substitute
Write the expression for the perimeter of the rectangular channel.
Substitute
Substitute
Calculation:
Substitute
Substitute
Conclusion:
The bottom breath of the rectangular channel is
The depth of the rectangular channel is
(c)
The dimension for the trapezoidal channel.

Answer to Problem 50P
The bottom breath of the trapezoidal channel is
The depth of the trapezoidal channel is
Explanation of Solution
Given Information:
The water flow rate is
Write the expression for the area of the trapezoidal channel.
Here, the trapezoidal angle is
Write the expression for the flow depth of the trapezoidal channel.
Write the expression for the inclined height of the trapezoidal section.
Write the expression for the perimeter of the trapezoidal channel.
Calculation:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Conclusion:
The bottom breath of the trapezoidal channel is
The depth of the trapezoidal channel is
Want to see more full solutions like this?
Chapter 13 Solutions
FLUID MECHANICS FUNDAMENTALS+APPS
- 1. The rotating steel shaft is simply supported by bearings at points of B and C, and is driven by a spur gear at D, which has a 6-in pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA =3000 lbĘ in. The shaft is machined from steel with Sy=60kpsi and Sut=80 kpsi. (1) Draw a shear force diagram and a bending moment diagram by F. According to your analysis, where is the point of interest to evaluate the safety factor among A, B, C, and D? Describe the reason. (Hint: To find F, the torque Tд is generated by the tangential force of F (i.e. Ftangential-Fcos20°) When n=2.5, K=1.8, and K₁ =1.3, determine the diameter of the shaft based on (2) static analysis using DE theory (note that fatigue stress concentration factors need to be used for this question because the loading condition is fatigue) and (3) a fatigue analysis using modified Goodman. Note) A standard diameter is not required for the questions. 10 in Darrow_forward3 N2=28 P(diametral pitch)=8 for all gears Coupled to 25 hp motor N3=34 Full depth spur gears with pressure angle=20° N₂=2000 rpm (1) Compute the circular pitch, the center-to-center distance, and base circle radii. (2) Draw the free body diagram of gear 3 and show all the forces and the torque. (3) In mounting gears, the center-to-center distance was reduced by 0.1 inch. Calculate the new values of center-to-center distance, pressure angle, base circle radii, and pitch circle diameters. (4)What is the new tangential and radial forces for gear 3? (5) Under the new center to center distance, is the contact ratio (mc) increasing or decreasing?arrow_forward2. A flat belt drive consists of two 4-ft diameter cast-iron pulleys spaced 16 ft apart. A power of 60 hp is transmitted by a pulley whose speed is 380 rev/min. Use a service factor (Ks) pf 1.1 and a design factor 1.0. The width of the polyamide A-3 belt is 6 in. Use CD=1. Answer the following questions. (1) What is the total length of the belt according to the given geometry? (2) Find the centrifugal force (Fc) applied to the belt. (3) What is the transmitted torque through the pulley system given 60hp? (4) Using the allowable tension, find the force (F₁) on the tight side. What is the tension at the loose side (F2) and the initial tension (F.)? (5) Using the forces, estimate the developed friction coefficient (f) (6) Based on the forces and the given rotational speed, rate the pulley set. In other words, what is the horse power that can be transmitted by the pulley system? (7) To reduce the applied tension on the tight side, the friction coefficient is increased to 0.75. Find out the…arrow_forward
- The tooth numbers for the gear train illustrated are N₂ = 24, N3 = 18, №4 = 30, №6 = 36, and N₁ = 54. Gear 7 is fixed. If shaft b is turned through 5 revolutions, how many turns will shaft a make? a 5 [6] barrow_forwardCE-112 please solve this problem step by step and give me the correct answerarrow_forwardCE-112 please solve this problem step by step and give me the correct answerarrow_forward
- CE-112 solve this problem step by step and give me the correct answer pleasearrow_forwardPlease do not use any AI tools to solve this question. I need a fully manual, step-by-step solution with clear explanations, as if it were done by a human tutor. No AI-generated responses, please.arrow_forwardPlease do not use any AI tools to solve this question. I need a fully manual, step-by-step solution with clear explanations, as if it were done by a human tutor. No AI-generated responses, please.arrow_forward
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE LPrinciples of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning




