Explanation Write the energy rate balance equation for one inlet and one outlet system. [ Q ˙ 1 + W ˙ 1 + m ˙ ( h 1 + V 1 2 2 + g z 1 ) ] − [ Q ˙ 2 + W ˙ 2 + m ˙ ( h 2 + V 2 2 2 + g z 2 ) ] = Δ E ˙ system (I) Here, the rate of heat transfer is Q ˙ , the rate of work transfer is W ˙ , the enthalpy is h and the velocity is V , the gravitational acceleration is g , the elevation from the datum is z and the rate of change in net energy of the system is Δ E ˙ system ; the suffixes 1 and 2 indicates the inlet and outlet of the system. Consider the nozzle operates at steady state. Hence, the rate of change in net energy of the system becomes zero. Δ E ˙ system = 0 Since, the gas passes through the adiabatic nozzle, the heat transfer rate is negligible i.e. Q ˙ = 0 . Also neglect the work transfer rates i.e. W ˙ = 0 . The inlet, outlet are at same elevation, the potential energy becomes negligible i.e. g z = 0 . The Equations (I) reduced as follows to obtain the exit velocity. [ 0 + 0 + m ˙ ( h 1 + V 1 2 2 + 0 ) ] − [ 0 + 0 + m ˙ ( h 2 + V 2 2 2 + 0 ) ] = 0 m ˙ ( h 1 + V 1 2 2 ) − m ˙ ( h 2 + V 2 2 2 ) = 0 m ˙ ( h 1 + V 1 2 2 ) = m ˙ ( h 2 + V 2 2 2 ) h 1 + V 1 2 2 = h 2 + V 2 2 2 V 2 2 2 − V 1 2 2 = h 1 − h 2 V 2 2 − V 1 2 = 2 ( h 1 − h 2 ) V 2 = V 1 2 + 2 ( h 1 − h 2 ) (II) It is given that the initial velocity is low. Hence, neglect the initial velocity i.e. V 1 = 0 . Substitute 0 for V 1 in Equation (II). V 2 = ( 0 ) 2 + 2 ( h 1 − h 2 ) = 2 ( h 1 − h 2 ) (III) Write formula for enthalpy departure factor ( Z h ) . Z h = ( h ¯ ideal − h ¯ ) T , P R u T cr (IV) Here, the molar enthalpy at ideal gas state is h ¯ ideal , the molar enthalpy and normal state is h ¯ , the universal gas constant is R u , and the critical temperature is T cr ; The subscripts T , P indicates the correspondence of given temperature and pressure. Rearrange the Equation (I) to obtain h ¯ . h ¯ = h ¯ ideal − Z h R u T cr (V) Refer Equation (V) express as two states of enthalpy difference (initial–final). h ¯ 1 − h ¯ 2 = ( h ¯ 1 − h ¯ 2 ) ideal − ( Z h 1 − Z h 2 ) R u T cr (VI) Here, the molar enthalpy difference is h ¯ 2 − h ¯ 1 . The enthalpy difference is expressed as follows. h 1 − h 2 = h ¯ 1 − h ¯ 2 M CO 2 (VII) Refer Table A-1, “Molar mass, gas constant, and critical-point properties”

8th Edition

ISBN: 9781307434316

Author: CENGEL

Publisher: INTER MCG

See similar textbooks

Videos

Question

Chapter 12.6, Problem 73P

To determine

The exit velocity of the carbon dioxide using generalized enthalpy departure chart.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.6, Problem 72P

Chapter 12.6, Problem 75P

Students have asked these similar questions

The state of stress at a point is σ = -4.00 kpsi, σy = 16.00 kpsi, σ = -14.00 kpsi, Try = 11.00 kpsi, Tyz = 8.000 kpsi, and T = -14.00 kpsi. Determine the principal stresses. The principal normal stress σ₁ is determined to be [ The principal normal stress σ2 is determined to be [ The principal normal stress σ3 is determined to be kpsi. kpsi. The principal shear stress 71/2 is determined to be [ The principal shear stress 7½ is determined to be [ The principal shear stress T₁/, is determined to be [ kpsi. kpsi. kpsi. kpsi.

Repeat Problem 28, except using a shaft that is rotatingand transmitting a torque of 150 N * m from the left bearing to the middle of the shaft. Also, there is a profile keyseat at the middle under the load. (I want to understand this problem)

Prob 2. The material distorts into the dashed position shown. Determine the average normal strains &x, Ey and the shear strain Yxy at A, and the average normal strain along line BE. 50 mm B 200 mm 15 mm 30 mm D ΕΙ 50 mm x A 150 mm F

Chapter 12 Solutions

THERMODYNAMICS(SI UNITS,INTL.ED)EBOOK>I

Ch. 12.6 - What is the difference between partial...Ch. 12.6 - Consider a function z(x, y) and its partial...Ch. 12.6 - Prob. 3P Ch. 12.6 - Conside the function z(x, y), its partial...Ch. 12.6 - Consider air at 350 K and 0.75 m3/kg. Using Eq....Ch. 12.6 - Consider air at 350 K and 0.75 m3/kg. Using Eq....Ch. 12.6 - 12–7 Nitrogen gas at 400 K and 300 kPa behaves as...Ch. 12.6 - Nitrogen gas at 800 R and 50 psia behaves as an...Ch. 12.6 - Prob. 9P Ch. 12.6 - Using the equation of state P(v a) = RT, verify...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The exit velocity of the carbon dioxide using generalized enthalpy departure chart.

Solution Summary: The author explains the exit velocity of the carbon dioxide using generalized enthalpy departure chart and the energy rate balance equation for one inlet and one outlet system.

Videos

The exit velocity of the carbon dioxide using generalized enthalpy departure chart.

Want to see the full answer?

Chapter 12 Solutions