Concept explainers
Saturated water vapor at 300°C is expanded while its pressure is kept constant until its temperature is 700°C. Calculate the change in the specific enthalpy and entropy using (a) the departure charts and (b) the property tables.
(a)
The change in specific enthalpy and entropy of saturated water per unit mass using departure charts.
Answer to Problem 72P
The change in specific enthalpy and entropy of saturated water per unit mass using departure charts is
Explanation of Solution
At ideal gas state, the enthalpy is the function of temperature only.
Write the formula for difference in molar specific enthalpy of water vapor at ideal gas state.
Here, the molar enthalpy at ideal gas state corresponding to the temperature is
Write the formula for change in molar specific entropy.
Here, the molar specific entropy at reference sate is
Write formula for enthalpy departure factor
Here, the molar enthalpy at ideal gas state is
Rearrange the Equation (III) to obtain
Refer Equation (IV) express as two states of enthalpy difference (final – initial).
Write formula for entropy departure factor
Here, the molar entropy at ideal gas state is
Rearrange the Equation (VI) to obtain
Refer Equation (VII) express as two states of entropy difference (final – initial).
Write the formula for enthalpy
Here, the molar enthalpy is
Refer Table A-1, “Molar mass, gas constant, and critical-point properties”.
The critical temperature and pressure of water vapor gas is as follows.
Refer Table A-1, “Molar mass, gas constant, and critical-point properties”.
The molar mass
The pressure is kept constant until its temperature reaches to
Refer Table A-4, “Saturated water-Temperature table”.
The saturation pressure corresponding to the temperature of
The reduced pressure
The reduced pressure
At initial:
Refer Figure A-29, “Generalized enthalpy departure chart”.
The enthalpy departure factor
Refer Figure A-30, “Generalized entropy departure chart”.
The entropy departure factor
At final:
Refer Figure A-29, “Generalized enthalpy departure chart”.
The enthalpy departure factor
Refer Figure A-30, “Generalized entropy departure chart”.
The entropy departure factor
Refer Table A-19, “Ideal-gas properties of water vapor,
Obtain the initial properties corresponding to the temperature of
Obtain the final properties corresponding to the temperature of
The universal gas constant
Conclusion:
Substitute
Equation (I).
Substitute
Substitute
Substitute
Substitute
Substitute
Thus, the change in specific enthalpy and entropy of saturated water per unit mass using departure charts is
(a)
The change in specific enthalpy and entropy of water vapor per unit mass using property tables.
Answer to Problem 72P
The change in specific enthalpy and entropy of water vapor per unit mass using property tables is
Explanation of Solution
At state 1:
The steam is at state of saturated vapor at the temperature of
Refer Table A-4, “Saturated water-Temperature table”.
The enthalpy
At state 2:
The water vapor is expanded to the temperature of
The pressure is kept constant until its temperature reaches to
Refer Table A-4, “Saturated water-Temperature table”.
The saturation pressure corresponding to the temperature of
Refer Table A-6, “Superheated water”.
Obtain the enthalpy
Conclusion:
The enthalpy changes are expressed as follows.
The entropy changes are expressed as follows.
Thus, the change in specific enthalpy and entropy of water vapor per unit mass using property tables is
Want to see more full solutions like this?
Chapter 12 Solutions
CENGEL'S 9TH EDITION OF THERMODYNAMICS:
- Generate the kinematic diagram of the following mechanisms using the given symbols. Then, draw their graphs and calculate their degrees of freedom (DoF) using Gruebler's formula. PUNTO 2. PUNTO 3. !!!arrow_forwardCreate a schematic representation of the following mechanisms using the given symbols and draw their graphs. Then, calculate their degrees of freedom (DoF) using Gruebler's formula. PUNTO 6. PUNTO 7.arrow_forwardhow the kinematic diagram of the following mechanisms would be represented using the given symbols? PUNTO 0. PUNTO 1. °arrow_forward
- Create a schematic representation of the following mechanisms using the given symbols and draw their graphs. Then, calculate their degrees of freedom (DOF) using Gruebler's formula. PUNTO 4. PUNTO 5. (0) Groundarrow_forwardDraw the graph of ALL the mechanisms and calculate their DoF using Gruebler's formula. PUNTO 0. PUNTO 1.arrow_forwardAn adjustable support. Construction designed to carry vertical load and is adjusted by moving the blue attachment vertically. The link is articulated at both ends (free to rotate) and can therefore only transmit power axially. Analytically calculate the force to which the link is subjected? Calculate analytically rated voltage in the middle of the link.? F=20kN Alpha 30 deg Rel 225 Mpans:5arrow_forward
- A swivel crane where the load is moved axially along the beam through the wagon to which the hook is attached. Round bar with a diameter of ∅30 mm. The support beam is articulated at both ends (free to rotate) and can therefore only transmit force axially. Calculate reaction force in the x-direction at point A? Calculate analytical reaction force in the y-direction of point A? Calculate nominal stress in the middle of the support beam?Lengt 5 mAlfa 25 degX=1.5mIPE300-steelmass:1000 kgarrow_forwardgot wrong answers help pleasearrow_forwardA crate weighs 530 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the xy plane. Point A is located at a height of h = 42 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom cc00 BY NC SA ↑ Z C b B У a D Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 30 in b 43 in 4.5 in The tension in rope AB is 383 x lb The tension in rope AC is 156 x lb The tension in rope AD is 156 x lbarrow_forward
- A block of mass m hangs from the end of bar AB that is 7.2 meters long and connected to the wall in the xz plane. The bar is supported at A by a ball joint such that it carries only a compressive force along its axis. The bar is supported at end B by cables BD and BC that connect to the xz plane at points C and D respectively with coordinates given in the figure. Cable BD is elastic and can be modeled as a linear spring with a spring constant k = 400 N/m and unstretched length of 6.34 meters. Determine the mass m, the compressive force in beam AB and the tension force in cable BC. Z C D (c, 0, d) (a, 0, b) A B y f m cc 10 BY NC SA 2016 Eric Davishahl x Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 8.1 m b 3.3 m с 2.7 m d 3.9 m e 2 m f 5.4 m The mass of the block is 68.8 The compressive force in bar AB is 364 × kg. × N. The tension in cable BC is 393 × N.arrow_forwardThe airplane weighs 144100 lbs and flies at constant speed and trajectory given by 0 on the figure. The plane experiences a drag force of 73620 lbs. 0 a.) If 11.3°, determine the thrust and lift forces = required to maintain this speed and trajectory. b.) Next consider the case where is unknown, but it is known that the lift force is equal to 7.8 times the quantity (Fthrust Fdrag). Compute the resulting trajectory angle and the lift force in this case. Use the same values for the weight and drag forces as you used for part a. 20. YAAY' Farag Ө Fthrust CC + BY NC SA 2013 Michael Swanbom Flift Fweight The lift force acts in the y' direction. The weight acts in the negative y direction. The thrust and drag forces act in the positive and negative x' directions respectively. Part (a) The thrust force is equal to 101,855 ☑ lbs. The lift force is equal to 141,282 ☑ lbs. Part (b) The trajectory angle 0 is equal to 7.31 ✓ deg. The lift force is equal to 143,005 ☑ lbs.arrow_forwardsimply supported beam has a concentrated moment M, applied at the left support and a concentrated force F applied at the free end of the overhang on the right. Using superposition, determine the deflection equations in regions AB and BC.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY