Explanation Given information: The weight of the panel ( W ) is 40 lb. The weight of the counterweight A ( W A ) is 25 lb. The friction is negligible for the system. Calculation: Case ( a ): Sketch the free body diagram of the panel as shown in Figure (1). Apply the Newton’s second law of motion along horizontal axis: Σ F x = m a x T − F = W g a (1) Here, m is the mass of the panel, T is the tension in the cord, F is the frictional force on the panel, g is the acceleration due to gravity, and a is the acceleration of the panel. The acceleration of counterweight has two components. Sketch the free body diagram of the counterweight A as shown in Figure (2). Refer Figure (2). Apply the Newton’s second law of motion along vertical axis: Σ F x = m a x − F = − W A g a F = W A g a (2) Apply the Newton’s second law of motion along horizontal axis: Σ F y = m a y T − W A = − W A g a W A − T = W A g a (3) Find the acceleration of the panel immediately after the system is released from rest in case ( a ). Add Equation (1), (2), and (3). T − F + F + W A − T = W g a + W A g a + W A g a W A = ( W + 2 W A ) a g a = W A g W + 2 W A Substitute 25 lb for W A , 40 lb for W , and 32.2 lb/ft 2 for g . a = ( 25 ) ( 32.2 ) 40 + 2 × 25 = 8.94 ft/s 2 ← Thus, the acceleration of the panel immediately after the system is released from rest in case ( a ) is 8.94 ft/s 2 ← _ . Find the tension in the cord immediately after the system is released from rest in case ( a ) using Equation (3); W A − T = W A g a Substitute 25 lb for W A , 40 lb for W , 32.2 lb/ft 2 for g , and 8.94 ft/s 2 for a . 25 − T = 25 32.2 ( 8.94 ) T = 18.06 lb Thus, the tension in the cord immediately after the system is released from rest in case ( a ) is 18.06 lb _ . Case ( b ): Sketch the free body diagram of the panel as shown in Figure (3). Refer Figure (3). Apply the Newton’s second law of motion along horizontal axis: Σ F x = m a x T = W g a (4) Sketch the free body diagram of the counterweight A as shown in Figure (2). Refer Figure (4). Apply the Newton’s second law of motion along vertical axis: Σ F y = m a y T − W A = − W A g a W A − T = W A g a (5) Find the acceleration of the panel immediately after the system is released from rest in case ( b )

11th Edition

ISBN: 9781259633133

Author: BEER

Publisher: MCG

See similar textbooks

Videos

Question

Chapter 12.1, Problem 12.29P

To determine

Find the acceleration of the panel and the tension in the cord immediately after the system is released from rest in each case.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.1, Problem 12.28P

Chapter 12.1, Problem 12.30P

Students have asked these similar questions

First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³

2/Y Y+1 2Cp Q1/ Show that Cda Az x P1 mactual Cdf Af R/T₁ 2pf(P1-P2-zxgxpf) Q2/ A simple jet carburetor has to supply 5 Kg of air per minute. The air is at a pressure of 1.013 bar and a temperature of 27 °C. Calculate the throat diameter of the choke for air flow velocity of 90 m/sec. Take velocity coefficient to be 0.8. Assume isentropic flow and the flow to be compressible. Quiz/ Determine the air-fuel ratio supplied at 5000 m altitude by a carburetor which is adjusted to give an air-fuel ratio of 14:1 at sea level where air temperature is 27 °C and pressure is 1.013 bar. The temperature of air decreases with altitude as given by the expression The air pressure decreases with altitude as per relation h = 19200 log10 (1.013), where P is in bar. State any assumptions made. t = ts P 0.0065h

36 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.2. 300lbs/ft member-1 member-2 30° Fig 3.2. https://brightspace.cuny.edu/d21/le/content/433117/viewContent/29873977/View

Chapter 12 Solutions

VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS

Ch. 12.1 - A 1000-lb boulder B is resting on a 200-lb...Ch. 12.1 - Marble A is placed in a hollow tube, and the tube...Ch. 12.1 - The two systems shown start from rest. On the...Ch. 12.1 - Blocks A and B are released from rest in the...Ch. 12.1 - People sit on a Ferris wheel at points A, B, C,...Ch. 12.1 - Crate A is gently placed with zero initial...Ch. 12.1 - Two blocks weighing WA and WB are at rest on a...Ch. 12.1 - Objects A, B, and C have masses mA, mB, and mC,...Ch. 12.1 - Prob. 12.4FBP Ch. 12.1 - Blocks A and B have masses mA and mB,...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.