Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 7ASRQ
Technician A uses a 30-degree stone for topping a 45-degree valve seat. Technician B uses a 60-degree stone to lower a 45-degree valve seat. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?
Technician A says that it takes about 1
pint of oil to raise the oil level from "add"
to "full." Technician B says that it takes
about 1 quart to raise it that much. Who is
correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
A technician is inspecting a vehicle and finds
the upper radiator hose is collapsed, and the
cooling system pulled into a vacuum when
cold. Technician A states that a leak in the
surge tank could be the cause. Technician B
states that the radiator cap is most likely
defective. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Chapter 12 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - Prob. 8RQCh. 12 - To ensure proper seating of the valve, the valve...Ch. 12 - When checking valve fit, contact between the valve...
Ch. 12 - If the valve face and valve seat do not contact...Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - Which of the following statements is not true?...Ch. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - When fitting a freshly ground valve into a freshly...Ch. 12 - Technician A says off-square springs may cause...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - Technician A uses a 30-degree stone for topping a...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Typically during a pressure test, the pressure should not drop more than_____ psi between shifts.arrow_forwardWhich of the following is not a type of valve guide seal? Positive Negative Umbrella O-ringarrow_forwardA compression test gave the following results: cylinder #1 = 155, cylinder #2 = 140, cylinder #3 = 110, cylinder #4 = 105. Technician A says that a defective (burned) valve is the most likely cause. Technician B says that a leaking head gasket could be the cause.arrow_forward
- 40) Technician A says Pascals law can be used to provide mechanical advantage. Technician B says a single hydraulic system is capable of providing different amounts of output pressures from a common system pressure. Which technician is correct? O Technician A O Technician B O Both technicians A and B O Neither technician A nor Barrow_forwardValves are favored because of their lower cost and lighter weight Correct answer plug ball poppet butterflyarrow_forwardHello, I have some diagrams I have filled out for practice that I would like to use to study for an exam. Can someone double check them and suggest corrections if needed? Thank youarrow_forward
- While looking at the results of an oil pressure test: Technician A says that higher than normal readings can be caused by using oil that is too thin. Technician B says that higher than normal readings can be expected on a cold engine. Who is correct? Technician A Technician Both A and B Neither A nor Barrow_forwardthe metring valve portion of combination valve fails .technician A says that this means the entire combination valve must be replaced.Technician B says that the metring part can be repaired who is correct?arrow_forwardThe velocity of flow increases when valve openings decreases Select one: O True O Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license