Fundamentals of Engineering Thermodynamics
8th Edition
ISBN: 9781118412930
Author: Michael J. Moran, Howard N. Shapiro, Daisie D. Boettner, Margaret B. Bailey
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 11.9, Problem 37CU
To determine
Indicate the following statement is true or false.
According to the additive pressure rule, the pressure of a gas mixture is expressible as the sum of the pressures exerted by the individual components, assuming each component occupies the entire volume at the mixture temperature.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
If the rods are made from a square section with the dimension as shown. Calculate the load
that will make point A move to the left by 6mm, E=228GPa.
2P-
P
A
80mm
B
200mm
2P
0.9m
1.3m
3.
9.
10.
The centrifugal tension in belts
(a) increases power transmitted
(b) decreases power transmitted
(c) have no effect on the power transmitted
(d) increases power transmitted upto a certain speed and then decreases
When the belt is stationary, it is subjected to some tension, known as initial tension. The value of this
tension is equal to the
(a) tension in the tight side of the belt
(b) tension in the slack side of the belt
(c) sum of the tensions in the tight side and slack side of the belt
(d) average tension of the tight side and slack side of the belt
The relation between the pitch of the chain (p) and pitch circle diameter of the sprocket (d) is given by
60°
(a) p=d sin
(c) p=d sin
(120°
T
where T Number of teeth on the sprocket.
90°
(b) p=d sin
T
180°
(d) p=d sin
T
OBJECTIVE TYPE QUESTIONS
1.
The maximum fluctuation of energy is the
2.
(a) sum of maximum and minimum energies
(b) difference between the maximum and minimum energies
(c) ratio of the maximum energy and minimum energy
(d) ratio of the mean resisting torque to the work done per cycle
In a turning moment diagram, the variations of energy above and below the mean resisting torque line
is called
(a) fluctuation of energy
(b) maximum fluctuation of energy
(c) coefficient of fluctuation of energy
(d) none of the above
Chapter 16: Turning Moment Diagrams and Flywheel 611
The ratio of the maximum fluctuation of speed to the mean speed is called
3.
(a) fluctuation of speed
(c) coefficient of fluctuation of speed
4.
(b) maximum fluctuation of speed
(a) none of these
The ratio of the maximum fluctuation of energy to the.......... is called coefficient of fluctuation of
energy.
(a) minimum fluctuation of energy
(b) work done per cycle
The maximum fluctuation of energy in a flywheel is equal to
5.…
Chapter 11 Solutions
Fundamentals of Engineering Thermodynamics
Ch. 11.9 - Prob. 1ECh. 11.9 - Prob. 2ECh. 11.9 - 3. What is an advantage of using the Redlich–Kwong...Ch. 11.9 - To determine the specific volume of superheated...Ch. 11.9 - Prob. 5ECh. 11.9 - Prob. 6ECh. 11.9 - Prob. 7ECh. 11.9 - Prob. 8ECh. 11.9 - Prob. 9ECh. 11.9 - Prob. 10E
Ch. 11.9 - Prob. 11ECh. 11.9 - Prob. 12ECh. 11.9 - Prob. 13ECh. 11.9 - Prob. 14ECh. 11.9 - Prob. 15ECh. 11.9 - Prob. 1CUCh. 11.9 - Prob. 2CUCh. 11.9 - Prob. 3CUCh. 11.9 - 4. Evaluate the compressibility factor Z of water...Ch. 11.9 - Prob. 5CUCh. 11.9 - Prob. 6CUCh. 11.9 - Prob. 7CUCh. 11.9 - Prob. 8CUCh. 11.9 - 9. For an ideal gas obtain expressions for the (a)...Ch. 11.9 - Prob. 10CUCh. 11.9 - Prob. 11CUCh. 11.9 - Prob. 12CUCh. 11.9 - Prob. 14CUCh. 11.9 - Prob. 15CUCh. 11.9 - Prob. 16CUCh. 11.9 - Prob. 17CUCh. 11.9 - Prob. 18CUCh. 11.9 - Prob. 19CUCh. 11.9 - Repeat parts (a)–(d) of Example 11.1 if the carbon...Ch. 11.9 - Prob. 21CUCh. 11.9 - Prob. 22CUCh. 11.9 - Prob. 23CUCh. 11.9 - Prob. 24CUCh. 11.9 - Prob. 25CUCh. 11.9 - Prob. 26CUCh. 11.9 - Prob. 27CUCh. 11.9 - Prob. 28CUCh. 11.9 - Prob. 29CUCh. 11.9 - Prob. 30CUCh. 11.9 - Prob. 31CUCh. 11.9 - Prob. 32CUCh. 11.9 - Prob. 33CUCh. 11.9 - Prob. 34CUCh. 11.9 - Prob. 35CUCh. 11.9 - Prob. 36CUCh. 11.9 - Prob. 37CUCh. 11.9 - Prob. 38CUCh. 11.9 - Prob. 39CUCh. 11.9 - Prob. 40CUCh. 11.9 - Indicate whether the following statements are true...Ch. 11.9 - Prob. 42CUCh. 11.9 - Prob. 43CUCh. 11.9 - Prob. 44CUCh. 11.9 - Prob. 45CUCh. 11.9 - Prob. 46CUCh. 11.9 - Prob. 47CUCh. 11.9 - Prob. 48CUCh. 11.9 - Prob. 49CUCh. 11.9 - Prob. 50CUCh. 11.9 - Owing to safety requirements, the pressure within...Ch. 11.9 - Ten pounds mass of propane have a volume of 2 ft3...Ch. 11.9 - The pressure within a 23.3-m3 tank should not...Ch. 11.9 - Estimate the pressure of water vapor at a...Ch. 11.9 - Prob. 7PCh. 11.9 - A rigid lank contains 1 kg of oxygen (O2) at p1 =...Ch. 11.9 - Prob. 11PCh. 11.9 - Prob. 13PCh. 11.9 - Prob. 14PCh. 11.9 - Prob. 15PCh. 11.9 - Prob. 16PCh. 11.9 - Prob. 17PCh. 11.9 - Prob. 18PCh. 11.9 - Prob. 20PCh. 11.9 - Prob. 21PCh. 11.9 - Prob. 22PCh. 11.9 - Prob. 23PCh. 11.9 - Using Eq. 11.35. check the consistency of
the...Ch. 11.9 - Prob. 25PCh. 11.9 - Prob. 26PCh. 11.9 - A gas enters a compressor operating at steady...Ch. 11.9 - Prob. 28PCh. 11.9 - Prob. 29PCh. 11.9 - The Mollier diagram provides a graphical...Ch. 11.9 - Derive the relation cp = −T(∂2g/∂T2)p.
Evaluating...Ch. 11.9 - Prob. 32PCh. 11.9 - Prob. 33PCh. 11.9 - Prob. 34PCh. 11.9 - Prob. 35PCh. 11.9 - Prob. 36PCh. 11.9 - At 0°C, the specific volumes of saturated solid...Ch. 11.9 - Prob. 38PCh. 11.9 - Prob. 39PCh. 11.9 - Prob. 42PCh. 11.9 - Prob. 43PCh. 11.9 - Prob. 44PCh. 11.9 - Prob. 46PCh. 11.9 - Prob. 47PCh. 11.9 - Prob. 48PCh. 11.9 - Prob. 49PCh. 11.9 - Prob. 50PCh. 11.9 - Prob. 51PCh. 11.9 - Prob. 52PCh. 11.9 - Prob. 53PCh. 11.9 - Prob. 54PCh. 11.9 - Develop expressions for the volume expansivity β...Ch. 11.9 - Prob. 56PCh. 11.9 - Prob. 57PCh. 11.9 - Prob. 58PCh. 11.9 - Prob. 59PCh. 11.9 - Prob. 60PCh. 11.9 - Prob. 61PCh. 11.9 - Prob. 62PCh. 11.9 - If the value of the specific heat cυ of air is...Ch. 11.9 - Prob. 65PCh. 11.9 - Prob. 66PCh. 11.9 - Prob. 67PCh. 11.9 - Prob. 68PCh. 11.9 - Prob. 69PCh. 11.9 - Determine the maximum Joule-Thomson inversion...Ch. 11.9 - Prob. 71PCh. 11.9 - Show that Eq. 11.77 can be written as
Using this...Ch. 11.9 - If the specific heat cv of a gas obeying the van...Ch. 11.9 - Prob. 75PCh. 11.9 - Prob. 76PCh. 11.9 - Prob. 77PCh. 11.9 - Prob. 78PCh. 11.9 - Prob. 79PCh. 11.9 - Prob. 80PCh. 11.9 - Prob. 81PCh. 11.9 - Prob. 82PCh. 11.9 - Prob. 83PCh. 11.9 - Prob. 84PCh. 11.9 - Prob. 85PCh. 11.9 - Prob. 86PCh. 11.9 - Prob. 87PCh. 11.9 - Prob. 88PCh. 11.9 - Oxygen (O2) undergoes a throttling process from...Ch. 11.9 - Prob. 90PCh. 11.9 - Prob. 91PCh. 11.9 - Prob. 92PCh. 11.9 - Prob. 93PCh. 11.9 - Prob. 94PCh. 11.9 - Prob. 95PCh. 11.9 - Prob. 96PCh. 11.9 - Prob. 97PCh. 11.9 - Prob. 99PCh. 11.9 - Prob. 100PCh. 11.9 - Prob. 101PCh. 11.9 - Prob. 102PCh. 11.9 - A rigid vessel initially contains carbon dioxide...Ch. 11.9 - Prob. 104PCh. 11.9 - Prob. 105PCh. 11.9 - Prob. 106PCh. 11.9 - Prob. 107PCh. 11.9 - Prob. 108PCh. 11.9 - Determine the fugacity, in atm, for
butane at 555...Ch. 11.9 - Using the equation of state of Problem 11.14(c),...Ch. 11.9 - Prob. 111PCh. 11.9 - Prob. 113PCh. 11.9 - Prob. 114PCh. 11.9 - Prob. 115PCh. 11.9 - Prob. 116PCh. 11.9 - Prob. 117PCh. 11.9 - Prob. 118PCh. 11.9 - Prob. 119PCh. 11.9 - Prob. 120PCh. 11.9 - Prob. 121PCh. 11.9 - Prob. 122PCh. 11.9 - Prob. 123PCh. 11.9 - A tank contains a mixture of 75% argon and 25%...Ch. 11.9 - Prob. 125PCh. 11.9 - Prob. 126PCh. 11.9 - Prob. 127PCh. 11.9 - Prob. 128P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- OBJECTIVE TYPE QUESTIONS 1. The velocity ratio of two pulleys connected by an open belt or crossed belt is 2. (a) directly proportional to their diameters (b) inversely proportional to their diameters (c) directly proportional to the square of their diameters (d) inversely proportional to the square of their diameters Two pulleys of diameters d, and d, and at distance x apart are connected by means of an open belt drive. The length of the belt is (a)(d+d₁)+2x+ (d₁+d₂)² 4x (b)(d₁-d₂)+2x+ (d₁-d₂)² 4x (c)(d₁+d₂)+ +2x+ (d₁-d₂)² 4x (d)(d-d₂)+2x+ (d₁ +d₂)² 4x 3. In a cone pulley, if the sum of radii of the pulleys on the driving and driven shafts is constant, then (a) open belt drive is recommended (b) cross belt drive is recommended (c) both open belt drive and cross belt drive are recommended (d) the drive is recommended depending upon the torque transmitted Due to slip of the belt, the velocity ratio of the belt drive 4. (a) decreases 5. (b) increases (c) does not change When two pulleys…arrow_forwardQ3: (10 MARKS) A piston with a weight of 29.4 N is supported by a spring and dashpot. A dashpot of damping coefficient c = 275 N.s/m acts in parallel with the spring of stiffness k = 2400 N/m. A fluctuating pressure p = 960 sin 30t N/m² acts on the piston, whose top surface area is 0.05 m². Determine the steady-state displacement as a function of time and the maximum force transmitted to the base. P=Po sin cot Warrow_forward9. Design a spur gear drive required to transmit 45 kW at a pinion speed of 800 r.p.m. The velocity ratio is 3.5 : 1. The teeth are 20° full-depth involute with 18 teeth on the pinion. Both the pinion and gear are made of steel with a maximum safe static stress of 180 MPa. Assume a safe stress of 40 MPa for the material of the shaft and key. 10. Design a pair of spur gears with stub teeth to transmit 55 kW from a 175 mm pinion running at 2500 r.p.m. to a gear running at 1500 r.p.m. Both the gears are made of steel having B.H.N. 260. Approximate the pitch by means of Lewis equation and then adjust the dimensions to keep within the limits set by the dynamic load and wear equation.arrow_forward
- 7. A motor shaft rotating at 1440 r.p.m. has to transmit 15 kW to a low speed shaft rotating at 500 r.p.m. The teeth are 20° involute with 25 teeth on the pinion. Both the pinion and gear are made of cast iron with a maximum safe stress of 56 MPa. A safe stress of 35 MPa may be taken for the shaft on which the gear is mounted. Design and sketch the spur gear drive to suit the above conditions. The starting torque may be assumed as 1,25 times the running torque. Ruins 20 LW at 100 nm to another shaft running approxiarrow_forward6. A two stage reduction drive is to be designed to transmit 2 kW; the input speed being 960 r.p.m. and overall reduction ratio being 9. The drive consists of straight tooth spur gears only, the shafts being spaced 200 mm apart, the input and output shafts being co-axial.arrow_forward2 A metal block of mass m = 10 kg is sliding along a frictionless surface with an initial speed Vo, as indicated below. The block then slides above an electromagnetic brake that applies a force FEB to the block, opposing its motion. The magnitude of the electromagnetic force varies quadratically with the distance moved along the brake (x): 10 FEB = kx², with k = 5 N m² V₁ = 8 m/s m = 10 kg FEB Frictionless surface Electromagnetic brake ⇒x Determine how far the block slides along the electromagnetic brake before stopping, in m.arrow_forward
- Q1: Determine the length, angle of contact, and width of a 9.75 mm thick leather belt required to transmit 15 kW from a motor running at 900 r.p.m. The diameter of the driving pulley of the motor is 300 mm. The driven pulley runs at 300 r.p.m. and the distance between the centers of two pulleys is 3 meters. The density of the leather is 1000 kg/m³. The maximum allowable stress in the leather is 2.5 MPa. The coefficient of friction between the leather and pulley is 0.3. Assume open belt drive.arrow_forward5. A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa. [Ans. m = 6 mm; b= 60 mm; Tp=24; T=96; Dp = 144mm; DG = 576 mm]arrow_forward4. G A micarta pinion rotating at 1200 r.p.m. is to transmit 1 kW to a cast iron gear at a speed of 192 r.p.m. Assuming a starting overload of 20% and using 20° full depth involute teeth, determine the module, number of teeth on the pinion and gear and face width. Take allowable static strength for micarta as 40 MPa and for cast iron as 53 MPa. Check the pair in wear.arrow_forward
- I want to solve these choicesarrow_forward2. A spur gear made of bronze drives a mid steel pinion with angular velocity ratio of 32: 1. The pressure angle is 14½. It transmits 5 kW at 1800 r.p.m. of pinion. Considering only strength, design the smallest diameter gears and find also necessary face width. The number of teeth should not be less than 15 teeth on either gear. The elastic strength of bronze may be taken as 84 MPa and of steel as 105 MPa. Lewis factor for 14½½ pressure angle may be taken 0.684 0.124 y = No. of teeth as [Ans. m 3 mm; b= 35 mm; Dp = 48 mm; D= 168 mm]arrow_forwardQ2. Determine the safety factors for the bracket rod shown in Figure 2 based on both the distortion-energy theory and the maximum shear theory and compare them. Given: The material is 2024-T4 aluminum with a yield strength of 47 000 psi. The rod length /= 6 in. and arm a = 8 in. The rod outside diameter od 1.5 in., id = 1 in, h=2 in., t=0.5 in., Load F= 1000 lb. Assumptions: The load is static and the assembly is at room temperature. Consider shear due to transverse loading as well as other stresses. (Note: solve in SI units) wall tube Figure 2 armarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Thermodynamics - Chapter 3 - Pure substances; Author: Engineering Deciphered;https://www.youtube.com/watch?v=bTMQtj13yu8;License: Standard YouTube License, CC-BY