Explanation Given Information: The x locations of her hip can be described by x ( t ) = 20 t + 0.2 sin ( 4 π 3 t ) . The y locations of her hip can be described by y ( t ) = 3.5 + 0.1 e − 0.3 t . Calculation: Write x and y coordinates to represent the position of the particle. x ( t ) = 20 t + 0.2 sin ( 4 π 3 t ) (1) y ( t ) = 3.5 + 0.1 e − 0.3 t sin ( 4 π 3 t ) (2) Calculate the x component value for 0 sec: Substitute 0 sec for t in Equation (1). x ( 0 ) = 20 ( 0 ) + 0.2 sin ( 4 π 3 ( 0 ) ) = 0 + 0 = 0 Calculate the y component value for 0 sec: Substitute 0 sec for t in Equation (2). y ( 0 ) = 3.5 + 0.1 e − 0.3 ( 0 ) = 3.6 ft Similarly calculate and tabulate the x and y coordinate value for time interval 0 ≤ t ≤ 3 sec in the below Table 1. Tabulate the x and y coordinate value for time interval 0 ≤ t ≤ 3 sec as in Table (1). t (s) x (ft) y (ft) 0 0 3.5 1 19.827 3.44 2 40.173 3.55 3 60 3.5 Plot the x-y value from table 1 for path of the hip as in Figure (1). Write the definition for velocity for Equations (1). v x = d x d t Substitute 20 t + 0.2 sin ( 4 π 3 t ) for x . v x = d ( 20 t + 0.2 sin ( 4 π 3 t ) ) d t Differentiate the above equation. v x = d ( 20 t + 0.2 sin ( 4 π 3 t ) ) d t = 20 + 4 15 cos ( 4 π 3 t ) (3) Write the definition for velocity for Equations (2). v y = d y d t Substitute 3

12th Edition

ISBN: 9781260804638

Author: BEER

Publisher: MCG

See similar textbooks

Videos

Question

Chapter 11.4, Problem 11.93P

To determine

Plot the path of the hip for the time interval 0≤t≤3sec.

The hip’s vertical position (y2) and the components of hip velocity (vx) and (vy) at time (t) 2 sec.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11.4, Problem 11.92P

Chapter 11.4, Problem 11.94P

Students have asked these similar questions

Figure 9-6 9-49 An aluminum alloy plate with dimensions 20 cm x 10 cm × 2 cm needs to be cast with a secondary dendrite arm spacing of 10-2 cm (refer to Figure 9-6). What mold constant B is required (assume n = 2 )? Secondary dendrite arm spacing (cm) - 10-1 10-2 10-3 10 41 0.1 1 Copper Zinc alloys Aluminum alloys 10 100 1,000 10,000 100,000 Solidification time (s)

9-72 Figure 9-29 shows a cylindrical riser attached to a casting. Compare the solidification times for each casting section and the riser and determine whether the riser will be effective. Figure 9-29 Т 3 6 3 8 3 6 Details A diagram shows the step-block casting. A cylinder of height "7" and diameter "3" is kept on a platform consisting of 2 steps. The width of the second step of the platform is labeled as "3". The horizontal length of the first step is labeled as "6." The horizontal length, width and height of the first step are labeled "6", "8" and "3".

6/94 Determine the minimum coefficient of static friction for which the bar can be in static equilibrium in the config- uration shown. The bar is uniform and the fixed peg at C is small. Neglect friction at B. A L PROBLEM 6/94 B L 22

Chapter 11 Solutions

VECTOR MECHANICS FOR ENGINEERS W/CON >B

Ch. 11.1 - A bus travels the 100 miles between A and B at 50...Ch. 11.1 - Two cars A and B race each other down a straight...Ch. 11.1 - A snowboarder starts from rest at the top of a...Ch. 11.1 - The motion of a particle is defined by the...Ch. 11.1 - The vertical motion of mass A is defined by the...Ch. 11.1 - A loaded railroad car is rolling at a constant...Ch. 11.1 - A group of hikers uses a GPS while doing a 40-mile...Ch. 11.1 - The motion of a particle is defined by the...Ch. 11.1 - A girl operates a radio-controlled model car in a...Ch. 11.1 - The motion of a particle is defined by the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Plot the path of the hip for the time interval 0 ≤ t ≤ 3 sec . The hip’s vertical position ( y 2 ) and the components of hip velocity ( v x ) and ( v y ) at time ( t ) 2 sec.

Solution Summary: The author calculates the x and y coordinates to represent the position of the particle.

Videos

Plot the path of the hip for the time interval 0≤t≤3sec.

The hip’s vertical position (y2) and the components of hip velocity (vx) and (vy) at time (t) 2 sec.

Want to see the full answer?

Chapter 11 Solutions

Plot the path of the hip for the time interval 0 ≤ t ≤ 3 sec . The hip’s vertical position ( y 2 ) and the components of hip velocity ( v x ) and ( v y ) at time ( t ) 2 sec.

Solution Summary: The author calculates the x and y coordinates to represent the position of the particle.

Videos

Plot the path of the hip for the time interval 0≤t≤3sec. The hip’s vertical position (y2) and the components of hip velocity (vx) and (vy) at time (t) 2 sec.

Want to see the full answer?

Chapter 11 Solutions

Plot the path of the hip for the time interval 0≤t≤3sec.

The hip’s vertical position (y2) and the components of hip velocity (vx) and (vy) at time (t) 2 sec.