Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 11, Problem 9R
Why should the feed roller drag prevent the spool from coasting to a stop when the feed stops?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What are the basic differences between the dividing heads?
Why should the adiabatic flame temperature be much higher for a pure oxygen feed than for an air feed?
What about the stretch for OA?
Chapter 11 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 11 - What items make up a basic semiautomatic welding...Ch. 11 - What must be done to the shielding gas cylinder...Ch. 11 - Why is the shielding gas valve "cracked" before...Ch. 11 - What causes the electrode to bird-nest?Ch. 11 - Why must all fittings and connections be tight?Ch. 11 - What parts should be activated by depressing the...Ch. 11 - What benefit does a welding wire's cast provide?Ch. 11 - What are the advantages of using a feed roller...Ch. 11 - Why should the feed roller drag prevent the spool...Ch. 11 - Why must you always wind the wire tightly into a...
Ch. 11 - How is the amperage adjusted on a GMA welder?Ch. 11 - What effect on the welding current does increasing...Ch. 11 - Using Table 11-1, determine the amperage if 400...Ch. 11 - What happens to the weld as the electrode...Ch. 11 - What is the effect on the weld of changing the...Ch. 11 - What are the advantages of adding oxygen or CO2 to...Ch. 11 - What reactive gases are used with argon for GMA...Ch. 11 - What are the advantages of using CO2 for making...Ch. 11 - What is mill scale?Ch. 11 - What type of porosity is most often caused by mill...Ch. 11 - What should the welder watch if the view of the...Ch. 11 - When making a vertical weld and it appears that...Ch. 11 - What are the advantages of making vertical down...Ch. 11 - How can small weld beads be maintained during...Ch. 11 - How can spatter be controlled on the nozzle when...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why does the preheat flame become slightly oxidizing when the cutting lever is released?arrow_forwardWhat is the maximum acceptable root face concavity on tubing?arrow_forwardReferring to Table 13-1, answer the following a. What would the range of the feed speed be for an amperage of 150 at 25 volts for an EM70-T 0.035-in. (09-mm) electrode? b. What would the approximate amperage be for an E70T-5 0045-in. (IQ-mm) electrode if it is being fed at a rate of 200 in. per minute (508 cm per minute)?arrow_forward
- Why should the filler pass penetration be limited in depth?arrow_forward14)arrow_forwardA engine develops power output for each two engine revolution. * Your answer It is the difference in expansion amounts between the cylinder head and pushrod that effectively increases the space between the valve stem and the rocker's arm. * Your answer On a four-stroke cycle reciprocating engine, which strokes are both valves close? * Intake Power Ignition Compression Exhaust It represents the net power output of the engine at the crankshaft. * Your answer If the fuel/air ratio is proper and ignition timing is correct, the combustion process should be completed just after center at the beginning of the power stroke. * Your answerarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Power Plant Explained | Working Principles; Author: RealPars;https://www.youtube.com/watch?v=HGVDu1z5YQ8;License: Standard YouTube License, CC-BY