Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 8ASRQ
When removing the piston and rod assemblies from a cylinder block; Technician A positions the throw of the crankshaft at the top of its stroke and removes the connecting rod nuts and cap. Technician B covers the rod bolts with protectors and pushes the piston and rod assembly out with the w’ooden hammer handle or wooden drift and supports the piston as it comes out of the cylinder. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What type of caps are used to hold the crankshaft in place once it’s installed in the block?
If the service information does not provide a loosening sequence for the cylinder head bolts, what should you do?
Tighten the cylinder head nut in
the order prescribed by---------
using the appropriate torque
-----,
by a torque wrench
The manufacturer
The company
The manual
None of them
Skip
means remove all
external components such as the
engine, dynamo ignition unit, and
injection pump
Connection
Assemble
Dismantling
Gathering
Skip
Chapter 11 Solutions
Automotive Technology
Ch. 11 - Describe how to inspect an oil pump.Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - List three types of compression rings.Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - How should the oil pump be primed when installing...Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...
Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 5MCCh. 11 - Which of the following are not typically found in...Ch. 11 - All of the following are functions of the...Ch. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...Ch. 11 - Technician A uses a feeler gauge and straightedge...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The clutch, or friction, disc is connected to the. a. engine crankshaft b. transmission input shaft c. transmission output shaft d. transmission countershaftarrow_forwardTechnician A says that a cylinder wall with too smooth a surface will prevent the piston rings from seating properly. Technician B says that a cylinder wall should have a crosshatch honing pattern. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhy is it important to loosen the cylinder head bolts in the recommended order?arrow_forward
- to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the machined surface true or falsearrow_forwardThe clutch, or friction, disc is connected to thearrow_forwardWhich of the following ensures proper timing of the intake and exhaust valve events? The length of the tappets relative to the pushrods. Proper pairing of the gear set joining the crankshaft to the camshaft. The pulse timer mounted in series with the piston. The installation of the flywheel key.arrow_forward
- While installing a timing belt: Technician A installs the belt, turns the crankshaft two full rotations, then applies tension to the belt. Technician B installs the belt, applies tension, then turns the crankshaft two full rotations. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile servicing a pair of aluminum cylinder heads: Technician A says it' needed, both heads must be machined equally and the same amount of material removed from each. Technician B replaces both heads if the warpage exceeds the specified allowable amount Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardA six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC. Who is correct and explain why? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says that piston ring end gaps should be the same for each ring on a piston. Technician B says that piston ring end gaps should be aligned before installing the piston into its bore. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that crankshaft counterweights offset the weight of the connecting rods and pistons. Technician B says that crankshaft counterweights are used to dampen crankshaft torsional vibrations. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardWhat is the importance of aligning the notches found on the cam-gear and crank-gear? (Select the best answer) Open and close the intake/exhaust valves Increase engine efficiency Ensure proper engine timing None of these answers are correctarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
First Law of Thermodynamics, Basic Introduction - Internal Energy, Heat and Work - Chemistry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=NyOYW07-L5g;License: Standard youtube license