You are designing a simple elevator system for an old warehouse that is being converted to loft apartments. A 22.500-N elevator is to be accelerated upward by connecting it to a counter-weight by means of a light (but strong!) cable passing over a solid uniform disk-shaped pulley. The cable does not slip where it is in contact with the surface of the pulley. There is no appreciable friction at the axle of the pulley, but its mass is 875 kg and it is 1.50 m in diameter, (a) What mass should the counterweight have so that it will accelerate the elevator upward through 6.75 m in the first 3.00 s, starting from rest? (b) What is the tension in the cable on each side of the pulley?
Figure P10.59
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
University Physics (14th Edition)
Additional Science Textbook Solutions
The Cosmic Perspective Fundamentals (2nd Edition)
College Physics
An Introduction to Thermal Physics
Physics (5th Edition)
The Cosmic Perspective (8th Edition)
College Physics: A Strategic Approach (3rd Edition)
- A wheel of radius 0.269 m, which we can model as a thin disk, is mounted on a frictionless horizontal axis. The mass of the wheel is 2.44 kg. A massless cord wrapped around the wheel is attached to a block of 4.16 kg that slides on a horizontal frictionless surface. If a horizontal force P with a magnitude of 10.1 N is applied to the block as shown below. If the wheel and block start at rest, and the block is moved through a displacement of 2.60 m what is the final angular velocity of the wheel in rad/s, assuming the cord does not slip. Parrow_forwardA solid cylinder (LaTeX: I\:=\frac{\:1}{2}MR^2 I = 1 2 M R 2 ) potter's wheel is a thick stone of radius 7 m with mass 5 kg. It freely rotates at 9 radian per second. The potter press a wet rag against the rim and exert a radially inward force of 10 N. If the coefficient of kinetic friction between the rag and the wheel is 0.6, find the time needed for the wheel to stop in seconds.arrow_forwardA participant in a "strongman" competition uses an old-fashioned device to move a large load with only muscle power. A 85-kg bucket of rocks is suspended from a sturdy, lightweight beam 0.78 m from a pivot. The man lifts the beam at its end, 3.0 m from the pivot, and holds it steady. Use g = 10 m/s2. How much force must the man apply, in Newtons? Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.arrow_forward
- A garage door is mounted on an overhead rail as shown below. The wheels at A and B have rusted so that they do not roll, but rather slide along the track. The coefficient of kinetic friction is 0.50. The distance between the wheels is 2.00 m, and each are 0.50 from the vertical sides of the door. The door is uniform and weighs 977 N. It is pushed to the left at constant speed by an external horizontal force. If the distance h is 1.54 m: a. What is the vertical component of the force exerted on the wheel A by the track? b. What is the vertical component of the force exerted on the wheel B by the track? c. Find the maximum value h can have without causing one wheel to leave the track. A В K 2.00 m h k- 3.00 m Figure 3. The two wheel track of a rusted garage door.arrow_forwardConsider the system shown in the figure below with m1 = 30.0 kg, m2 = 13.4 kg, R = 0.300 m, and the mass of the pulley M = 5.00 kg. Object m2 is resting on the floor, and object m1 is 4.50 m above the floor when it is released from rest. The pulley axis is frictionless. The cord is light, does not stretch, and does not slip on the pulley. a) Calculate the time interval required for m1 to hit the floor (in second). b) Calculate the time required again if the pulley were massless (in second)?arrow_forwardWhat? This problem again? Not exactly. A block with mass m,ị = 3.00 kg sits on a horizontal table and is attached to a rope. The rope then passes over a MASSIVE pulley this time and is attached to a block of mass m2 = 2.00 kg, which hangs vertically (see picture). The coefficient of kinetic friction of the interface between the table and m, is 0.1. You may assume the pulley section is a disk with a mass of 2 kg. We will keep the pulley frictionless for brevity. Ideal disk pulley with mass Find the acceleration of the blocks using your choice of either Newton's Laws or the energy conservation method. Yes, I can actually read your minds from here; of 2 kg and the answer is no, you do not need the radius of the pulley.arrow_forward
- Consider the system shown in the figure below with m1 = 30.0 kg, m2 = 13.4 kg, R = 0.300 m, and the mass of the pulley M = 5.00 kg. Object m2 is resting on the floor, and object m1 is 4.50 m above the floor when it is released from rest. The pulley axis is frictionless. The cord is light, does not stretch, and does not slip on the pulley. Calculate the time required again if the pulley were massless (in second)?arrow_forwardJohn is pushing his daughter Rachel in a wheelbarrow when it is stopped by a brick 8.00 cm high (see the figure below). The handles make an angle of 0 = 18.5° with the ground. Due to the weight of Rachel and the wheelbarrow, a downward force of 403 N is exerted at the center of the wheel, which has a radius of 15.0 cm. Assume the brick remains fixed and does not slide along the ground. Also assume the force applied by John is directed exactly toward the center of the wheel. (Choose the positive x-axis to be pointing to the right.) (a) What force (in N) must John apply along the handles to just start the wheel over the brick? (b) What is the force (magnitude in kN and direction in degrees clockwise from the -x-axis) that the brick exerts on the wheel just as the wheel begins to lift over the brick? magnitude kN direction ° clockwise from the -x-axisarrow_forwardA 65 kg student is in a car traveling at 25 m/s on a hill of radius 110 m. When the car is at the top of the hill, what upward force does the seat exert on the student? A 4.2 m long uniform post is supported by a cable having a tension of 1 700 N. What is the mass of this post?arrow_forward
- You are part of the stage crew for a theatrical company and are designing an apparatus to support an actor of mass 65.0 kg who is to “fly” down to the stage during the performance of a play. You attach the actor’s harness to a 130-kg sandbag by means of a lightweight steel cable running smoothly over two frictionless pulleys as in 8.5a. You need 3.00 m of cable between the harness and the nearest pulley so that the pulley can be hidden behind a curtain. For the apparatus to work successfully, the sandbag must never lift above the floor as the actor swings from above the stage to the floor. Let us call the initial angle that the actor’s cable makes with the vertical θ. What is the maximum value θ can have before the sandbag lifts off the floor?arrow_forwardA 10.0-kg monkey climbs auniform ladder with weight w =1.20 x 102 N and length L =3.00 mas shown in Figure P8.94. The ladderrests against the wall at an angleof θ = 60.0°. The upper and lowerends of the ladder rest on frictionlesssurfaces, with the lower endfastened to the wall by a horizontalrope that is frayed and that can support a maximum tension of only 80.0 N. (a) Draw aforce diagram for the ladder. (b) Find the normal forceexerted by the bottom of the ladder. (c) Find the tensionin the rope when the monkey is two-thirds of the way up theladder. (d) Find the maximum distance d that the monkeycan climb up the ladder before the rope breaks. (e) If thehorizontal surface were rough and the rope were removed,how would your analysis of the problem be changed andwhat other information would you need to answer parts (c)and (d)?arrow_forwardX Incorrect. In the figure, a small block of mass m = 0.014 kg can slide along the frictionless loop-the-loop, with loop radius R = 12 cm. The block is released from rest at point P, at height h = 5R above the bottom of the loop. What are the magnitudes of (a) the horizontal component and (b) the vertical component of the net force acting on the block at point Q? (c) At what height h should the block be released from rest so that it is on the verge of losing contact with the track at the top of the loop? (On the verge of losing contact means that the normal force on the block from the track has just then become zero). TEP (a) Number i 0.06 (b) Number Number i h Units Units Units QT R Y J 000arrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON