Elementary Principles of Chemical Processes
Elementary Principles of Chemical Processes
4th Edition
ISBN: 9780470616291
Author: Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher: WILEY
bartleby

Videos

Textbook Question
Book Icon
Chapter 10, Problem 10.28P

An iron bar 2.00 cm × 3.00 cm × 10.0 cm at a temperature of 95°C is dropped into a barrel of water at 25°C. The barrel is large enough so that the water temperature rises negligibly as the bar cools. The rate at which heat is transferred from the bar to the water is given by the expression

   Q ˙ ( J / min ) = U A ( T b T w )

where U[= 0.050 J/(min?cm2?°C)] is a heat transfer coefficient, A(cm2) is the exposed surface area of the bar, and Tb(°C) and TW(°C) are the surface temperature of the bar and the water temperature, respectively. The heat capacity of the bar is 0.460 J/(g? °C). Heat conduction in iron is rapid enough for the temperature Tb(t) to be considered uniform throughout the bar.

  1. Write an energy balance on the bar, assuming that all six sides are exposed. Your result should be an expression for dTb/dt and an initial condition.
  2. Without integrating the equation, sketch the expected plot of Tbversus t, labeling the values of Tbat t = 0 and t ? 8.

  • Derive an expression for Tb(t) and check it three ways. How long will it take for the bar to cool to 30°C?
  • Blurred answer
    Students have asked these similar questions
    Problem 1) A fractional factorial design has been used to study on the effect of 3 parameters including adsorbent concentration (300 and 500 ppm), pH value (4 and 10) and reaction time (6 and 12 hours) on the adsorption capacity of a composite for removing of methylene blue from a wastewater. If the results obtained for two repetitions of the tests are according to the following table, it is desirable: A) Design Resolution Y₁ Y₂ Run (mg/g) (mg/g) B) Drawing graphs of the effect of each parameter on the adsorption capacity 1 28 26 2 36 34 C) Analysis of interactions 3 18 20 D) Calculate the effects percentage of each parameter and error 4 32 30 E) Determining the optimum conditions to achieve the highest adsorption capacity
    Thermophysical Properties of Petroleum Fractions and Crude Ofls 67 3.4. A gas oil has the following TBP distillation data Volume % TBP (°C) 0 216 10 243 30 268 50 284 70 304 90 318 95 327 100 334 It also has an average boiling point of 280 °C and an average density of 0.850 g/cm³. (a) Split this gas oil fraction into five pseudo-components. Calculate T., Pc and w for each pseudo-component. (b) Calculate T, Pc and w for the whole gas oil fraction. (c) Calculate the enthalpy of this gas oil fraction at 400 °C using the Lee- Kessler correlation with a reference state of ideal gas at 273.15 K.
    3.3. Use the following crude assay data with crude API of 36 to estimate cut vol%, critical properties and molecular weight for Light Naphtha (90- 190 °F) and Kerosene (380-520 °F). In addition, calculate the fractions of paraffins, naphthenes and aromatics in the two cuts. ASTM D86 (°F) Volume % Cum vol% SG 86 0.0 0.0 122 0.5 0.5 0.6700 167 1.2 1.7 0.6750 212 1.6 3.3 0.7220 257 2.7 6.0 0.7480 302 3.1 9.1 0.7650 347 3.9 13.0 0.7780 392 4.7 17.7 0.7890 437 5.7 23.4 0.8010 482 8.0 31.4 0.8140 527 10.7 42.1 0.8250 584 5.0 47.1 0.8450 636 10.0 57.1 0.8540 689 7.8 64.9 0.8630 742 7.0 71.9 0.8640 794 6.5 78.4 0.8890 20.8 99.2 0.9310

    Additional Engineering Textbook Solutions

    Find more solutions based on key concepts
    Knowledge Booster
    Background pattern image
    Chemical Engineering
    Learn more about
    Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemical-engineering and related others by exploring similar questions and additional content below.
    Similar questions
    SEE MORE QUESTIONS
    Recommended textbooks for you
    Text book image
    Introduction to Chemical Engineering Thermodynami...
    Chemical Engineering
    ISBN:9781259696527
    Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
    Publisher:McGraw-Hill Education
    Text book image
    Elementary Principles of Chemical Processes, Bind...
    Chemical Engineering
    ISBN:9781118431221
    Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
    Publisher:WILEY
    Text book image
    Elements of Chemical Reaction Engineering (5th Ed...
    Chemical Engineering
    ISBN:9780133887518
    Author:H. Scott Fogler
    Publisher:Prentice Hall
    Text book image
    Process Dynamics and Control, 4e
    Chemical Engineering
    ISBN:9781119285915
    Author:Seborg
    Publisher:WILEY
    Text book image
    Industrial Plastics: Theory and Applications
    Chemical Engineering
    ISBN:9781285061238
    Author:Lokensgard, Erik
    Publisher:Delmar Cengage Learning
    Text book image
    Unit Operations of Chemical Engineering
    Chemical Engineering
    ISBN:9780072848236
    Author:Warren McCabe, Julian C. Smith, Peter Harriott
    Publisher:McGraw-Hill Companies, The
    Introduction to Nonreactive Processes Without Phase Change; Author: NPTEL-NOC IITM;https://www.youtube.com/watch?v=1Okp7895M6I;License: Standard YouTube License, CC-BY