A special-purpose eye bolt of shank diameter d = 0.50 in. passes through a hole in a steel plate of thickness r, = 0.75 in. (see figure) and is secured by a nut with thickness t = 0.25 in. The hexagonal nut bears directly against the steel plate. The radius of the circumscribed circle for the hexagon is r = 0,40 in. (which means that each side of the hexagon has length 0.40 in.). The tensile forces in three cables attached to the eye bolt are T = 800 lb. T, = 550 lb., andT: = 1241 lb. (a) Find the resultant force acting on the cye bolt. (b) Determine the average bearing stress o, between the hexagonal nut on the eye bolt and the plate. (c) Determine the average shear stress TN in the nut and also in the steel plate. 30 Cables Nut 30 Eye bolt T3 Steel plate

A special-purpose eye bolt of shank diameter d = 0.50 in. passes through a hole in a steel plate of thickness r, = 0.75 in. (see figure) and is secured by a nut with thickness t = 0.25 in. The hexagonal nut bears directly against the steel plate. The radius of the circumscribed circle for the hexagon is r = 0,40 in. (which means that each side of the hexagon has length 0.40 in.). The tensile forces in three cables attached to the eye bolt are T = 800 lb. T, = 550 lb., andT: = 1241 lb. (a) Find the resultant force acting on the cye bolt. (b) Determine the average bearing stress o, between the hexagonal nut on the eye bolt and the plate. (c) Determine the average shear stress TN in the nut and also in the steel plate. 30 Cables Nut 30 Eye bolt T3 Steel plate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The built-up beam is subjected to a moment of M = 80 kNm. Variable d₁ d₂ d3 da Values for the figure are given in the following table. Note the figure may not be to scale. d5 d3 de d₁ Value 128 mm 22 mm 276 mm 11 mm 138 mm d4 12 mm M₁ de d5 a. Determine the distance from the Neutral Axis to the top of the beam, N.A. b. Determine the mass moment of inertia of the beam, I. Determine the max compressive stress acting on the beam, compression c. d. Determine the max tensile stress acting on the beam, tension.
Q3: A hexagonal cross section bar as shown in Figure (2) below, is used as a simply supported beam. The beam carries a central load of 60 kN. Draw the shear stress distribution diagram for a section of the beam at quarter of the beam length from the left hand support. Figure (2) 25 mm 30° 30°
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Polar Moment of Inertia of the Post?
In the system shown in the figure, 2 sheets are connected to each other with the help of rivets with equal diameters and are forced by the force F. Of the 16 rivet slots shown in the figure, only the rivets shown in the brackets were used, and holes were drilled only for the specified rivets (16 holes on the sheet are NOT available. Only A4, B1, C1, D3 are holes.) i) Determine the center of rotation of the rivets. ii) Determine the rivet diameter required for the system to be safe.
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…
Q.3. For figure Q3, find rivet diameter, where t = 100MPa ? 20mm O O 30mm 1909 20mm- 30mm Fig.Q.3 4 KN 25 550mm-
Problem: I+12 For the given compound curve (see figure): a. Determine R, and R2. b. Determine T, and T2. c. Determine C, and C2. d. Determine L, and L2. e. If the stationing of PC is at 10 + 304.62 m, determine the stationing of PCC and PT. T+T2 РСС Pl, I = 12° I = 15° Pl2 L2 T, PC6 (Sta PC = 10 + 304.62) PT Long chord = 300m I = 15° R2 R1 'O2 I = 12° R,
A torsional moment T = 5,382 Nm and a load P = 55,253 N are applied at the same time to a circular hollow shaft of unknown length L, as shown in Figure Q5. The load P is offset from the centre of the circular cross-section by a distance e = 6 mm. The shaft has an inner diameter d = 43 mm and an outer diameter D = 97 mm. Point A in Figure Q5 is on the outer surface of the shaft. Figure 5 Calculate the direct (or normal) stress in the x-direction σx at point A (the 'x-direction' is along the longitudinal axis of the shaft, along its length L). Use π = 3.14159 if needed. Calculate your answer in the unit: mega-Pascal (MPa). Report you answer to 3 decimal places.
A 28 mm diameter rod with a 30 mm diameter handle as shown in Figure Q1 has two 90 degree bends. The handle is attached to the wall at 'A' while 1.8kN load is applied at the end of the rod at 'E'. Calculate Maximum Shear Stress at location 'A' and 'B' and determine it critical location. Bending load at point 'A'? Bending load at point 'B'? (Nm) Torsion load at rod; 'T'? Normal Stress due to bending load at point 'A'? (MPashear Stress due to torsion load at point 'A'? (MPa) 1st Principle stress at point 'A' (max principle stress)? (MPa Maximum shear stress at point 'B'? Critical Location? (L1) 170 $30- (L2) в 470 $28- F= 1.8kN| E 300 100 (L3) D Figure Q1