Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 1, Problem 17ETSQ
To determine
The material which satisfies all design requirements.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The strength of titanium is 448.16 MPa when the grain size is 17.02 μm and565.4 MPawhen the grain size is0.8μm. What average grain size (in nm) is required to achieve a strength of approximately 839 MPa?
Material A is known as a high strength material and Material B has high toughness. Explain the difference between properties of Materials A and B.
Three materials X, Y, and Z are available for a certain usage. Any material selected must have a good
weldability. Tensile strength, stiffness, stability and fatigue strength are required with fatigue strength considered
being the most important and stiffness the least important of these factors. The three materials are rated as follows in
these factors.
Properties
X
Y
Weldability
Excellent
Рoor
Good
Tensile strength
G
E
Fair
Stiffness
Very Good
G
G
Stability
G
E
G
Fatigue strength
F
G
E
Which material should be selected? Explain your choice.
Chapter 1 Solutions
Materials Science And Engineering Properties
Ch. 1 - Prob. 1CQCh. 1 - Prob. 2CQCh. 1 - Prob. 3CQCh. 1 - Prob. 4CQCh. 1 - Alumina (A12O3) is a(n) _________ material.Ch. 1 - Prob. 6CQCh. 1 - Prob. 7CQCh. 1 - Prob. 8CQCh. 1 - Prob. 9CQCh. 1 - Prob. 10CQ
Ch. 1 - Prob. 11CQCh. 1 - Prob. 12CQCh. 1 - Prob. 13CQCh. 1 - Prob. 14CQCh. 1 - Prob. 15CQCh. 1 - Prob. 16CQCh. 1 - Prob. 17CQCh. 1 - Prob. 18CQCh. 1 - Prob. 19CQCh. 1 - In the process of vulcanization the LCMs in latex...Ch. 1 - Prob. 21CQCh. 1 - Prob. 22CQCh. 1 - Prob. 23CQCh. 1 - Prob. 24CQCh. 1 - Prob. 25CQCh. 1 - Prob. 26CQCh. 1 - Prob. 27CQCh. 1 - Prob. 28CQCh. 1 - Prob. 29CQCh. 1 - Prob. 30CQCh. 1 - Prob. 31CQCh. 1 - Prob. 1ETSQCh. 1 - Prob. 2ETSQCh. 1 - Prob. 3ETSQCh. 1 - Prob. 4ETSQCh. 1 - Prob. 5ETSQCh. 1 - Prob. 6ETSQCh. 1 - Prob. 7ETSQCh. 1 - Prob. 8ETSQCh. 1 - Prob. 9ETSQCh. 1 - Prob. 10ETSQCh. 1 - Prob. 11ETSQCh. 1 - Prob. 12ETSQCh. 1 - Prob. 13ETSQCh. 1 - Prob. 14ETSQCh. 1 - Prob. 15ETSQCh. 1 - Prob. 16ETSQCh. 1 - Prob. 17ETSQCh. 1 - Prob. 1DRQ
Knowledge Booster
Similar questions
- The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.arrow_forward20)arrow_forwardMake a comparison between polymers and ceramics based on (a) mechanical properties and (b) on molecular structures under the effect of heating to temperatures.arrow_forward
- 16) Which of the following mechanical properties can be measured / calculated from this tensile stress-strain graph of a generic metal alloy? (pick all that apply) a. Poisson's ratio b. Elastic modulus C. Shear modulus d. Flexural modulus e. Fracture toughness 17) Interstitial sites in a FCC lattice are called a. Rhombohedral and cubic b. Cubic and hexagonal C. Monoclinic and triclinic Stress (MPa) 2000 MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0.000 0.020 0.040 Strain 0.060 0.080 d. Tetrahedral and octahedral e. Heterogeneous and homogeneous 18) Traditional photovoltaics rely on which structural feature to separate charge carriers? a. The p-n junction b. The grain boundaries C. The twin boundaries d. The electron-hole pair e. The band gap 19) The process by which lithium ions move in to and out of graphite in a lithium-ion battery is called a. Intercalation b. Stacking C. Precipitation d. Phase combination e. lonization 20) A polymer obtained by the polymerization of two types…arrow_forwardGiven your understanding of what initiates and controls failure in materials, which of the following will increase the failure strength or lifetime of a test piece or component and why? a. Decreasing the difference between the maximum and minimum stress values, as this effects the stress concentration factor b. Decreasing the temperature below the brittle-ductile transition temperature, to make it harder C. Polishing to reduce surface defects Od. Increasing its volume, to give a larger cross sectional area Oe. Increasing the grain size so there are less grain boundaries to initiate failurearrow_forwardFive classes of ceramic materials have been defined.arrow_forward
- What would you expect if you have a 6061 aluminum alloy bar, heat it for 1 hour in the oven forming a single phase, then severely temper it in water and then heat it at 150 ° for 6 hours. ? a) ductility is increased b) increases yield stress c) hardness is reduced d) the material is over-aged and the yield stress is reducedarrow_forwardTask (3) you are asked to perform tensile test on specimens of two different materials (A and B) and you obtained the stress-strain diagram of the two specimens as shown in Figure 2: 400 350 300 250 Material A 200 150 100 50 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 Strain (mm/mm) 50 Material B 30 20 10 0.02 0.04 0.06 0.08 0.1 Strain (mm/mm) Figure 2: Tensile Test Analysis Stress (MPa) Stress (MPa)arrow_forwardMechanical Properties-Metals For a bronze alloy, the stress at which plastic deformation begins is 295 MPa and the modulus of elasticity (E) is 108 GPa. (a) What is the maximum load (Fy) that can be applied to a specimen having a cross-sectional area of 314 mm2 without plastic deformation? (b) If the original specimen length is 142 mm, what is the maximum length to which it may be stretched without causing plastic deformation?arrow_forward
- Which of the following is correct when we increase the volume fraction porosity of a ceramic material? both the flexural strength and modulus of elasticity decreases flexural strength decreases, while modulus of elasticity increases flexural strength increases, while modulus of elasticity decreases both the flexural strength and modulus of elasticity increasesarrow_forwardPlease solve the following problem step by step so I can understand.arrow_forwardAnother of the steel components manufactured by michael's company is steel railway track sections. Thecomponent has a length of 120m (at a temperature of -10°C) and is to be exposed to a temperaturerange of -10°C to 55°C. In order to calculate the gaps which need to be left between the sections michael'scustomer needs to determine the maximum length which each railway track section will expand to andmichael have been asked to carry out the calculation for them. michael have also been instructed to determinethe percentage change in volume and surface area when exposed to the same initial and finaltemperatures. The customer has informed him that the cross sectional profile of the railway track isrectangular and of breadth 14cm and height 32cm. Assume the coefficient of thermal expansion ofsteel is 12x10-6 /°C. Briefly discuss the changes that occur with in the steel as a result of the change intemperature.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning