Your employer asks you to build a 23-cm-long solenoid with an interior field of 5.3 mT . The specifications call for a single layer of wire, wound with the coils as close together as possible. You have two spools of wire available. Wire with a #18 gauge has a diameter of 1.02 mm and has a maximum current rating of 6 A. Wire with a #26 gauge is 0.41 mm in diameter and can carry up to 1 A. Part B What current will you need? Express your answer to two significant figures and include the appropriate units.

Your employer asks you to build a 23-cm-long solenoid with an interior field of 5.3 mT . The specifications call for a single layer of wire, wound with the coils as close together as possible. You have two spools of wire available. Wire with a #18 gauge has a diameter of 1.02 mm and has a maximum current rating of 6 A. Wire with a #26 gauge is 0.41 mm in diameter and can carry up to 1 A. Part B What current will you need? Express your answer to two significant figures and include the appropriate units.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A2.10 cm x 2.10 cm square loop of wire with resistance 1.00×10-2 has one edge parallel to a long straight wire. The near edge of the loop is 1.10 cm from the wire. The current in the wire is increasing at the rate of 120 A/s.
In the accompanying figure, the rails, connecting end piece, and rod all have a resistance per unit length of 2.0 Ω/cm. The rod moves to the left at v = 3.0 m/s. If B = 0.75 T everywhere in the region, what is the current in the circuit (a) when a = 8.0 cm? (b) when a = 5.0 cm? Specify also the sense of the current flow.
An intrepid physics student transports a loop of wire from their hometown all the way to Earth's north magnetic pole. The loop has a radius ofr = 50 cm and a total resistance 75 m2, and the plane of the loop is held parallel to the ground at all times. In their hometown, Earth's magnetic 35 µT and points slightly into the ground, making an angle of 0 = 15° with a line that points due north. At the north magnetic pole, Earth's magnetic field 60 µT and points directly into the ground. If the student completed this journey over the course 48 hours, then what was the average current induced in the loop? Provide both the magnitude and direction of the current (as viewed from above the loop), and include a sketch of the "initial" and "final" configurations as part of of R field has a magnitude of B; has a magnitude of Bf of t your representation.
A 2100-turn solenoid is 1.5 m long and 15 cm in diameter. The solenoid current is increasing at 1.1 kA/s. A. Find the current in a 10cm-diameter wire loop with resistance 6.0 Ω lying inside the solenoid and perpendicular to the solenoid axis. B. Repeat for a similarly oriented 25cm-diameter loop with the same resistance, lying entirely outside the solenoid.
There are two concentric tungsten wire loops; a 4 cm radius loop and a 33 cm radius loop. The cross-sectional area of each wire is 0.009 m2. The current in the larger loop goes from 0 A to a counterclockwise 9 A in 5.9 10-4 s. Find the voltage & current in the smaller loop during the stated time interval. Assume the B-field of the larger loop is uniform (though not constant) across the smaller loop. V = I =
A coil of radius 3 cm has 60 turns of Cu wire of diameter 4 mm. The plane of the coil is perpendicular to a field that changes at the rate of 0.2 T/s. What is the power loss in the coil? The resistivity of Cu is 1.7 × 10-8 S. m. mW
Five parallel wires carry currents into or out of the page, as shown in the diagram below. The line integral of B around the loop (in the direction indicated) is +µoI where | = 1.0 A. I,=4.0A Iz=8.0A L=1.0A I=7.0A ? Is What is the unknown current I5? OA. 8.0 A out of the page. 8.0 A into the page. 5.0 A into the page. 5.0 A out of the page.
"1 @ 2 W S d X The figure is a cross section through three long wires with linear mass density 54.0 g/m. They each carry equal currents in the directions shown. The lower two. wires are 4.0 cm apart and are attached to a table. ( Figure 1) Figure ** #1 m 3 E D 8.0 F3 $ 4 R F a FA C JL V 1 of 1 % 5 T S FS G A 6 B Part A What current I will allow the upper wire to "float" so as to form an equilateral triangle with the lower wires? Express your answer with the appropriate units. Fo Y Provide Feedback HÅ Value Submit Request Answer H & 7 N 84 F7 U J Units 8 DII FB I M 9 K ? DD F9 O 1 delet
A square wire with 2 m sides is perpendicular to a uniform magnetic field, with half the area of the loop in the field as shown in the figure. The loop contains a 20 V battery with negligible resistance. If the magnitude of the field varies with time according to B = 1.1410 - 0.8500 t with B in teslas and t in seconds, what is the total emf in the circuit?
7 A Z S 30 H command 9. An electric power station that operates at 35 kV and uses a 10:1 step-up ideal transformer is producing 34 MW (Mega- Watt) of power that is to be sent to a big city which is located 300 km away with only 2.5% loss. Each of the two wires are made of copper (resistivity = 1.72 x 10-22.m). What is the diameter of the wires? X 0.85 cm x E 30 R 5 T 6 DEL LL B MacBook Air H N 8 J D 1 M ( 9 K MOSISO A P - command ? option
It is desired to construct a solenoid that will have a resistance of 4.65 N (at 20°C) and produce a magnetic field of 4.00 x 10-2T at its center when it carries a current of 3.85 A. The solenoid is to be constructed from copper wire having a diameter of 0.500 mm. If the radius of the solenoid is to be 1.00 cm, determine the following. (The resistivity of copper at 20°C is 1.7 x 10-8 n. m.) (a) the number of turns of wire needed to build the solenoid 853.2 v turns (b) the length the solenoid should have 426 Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. cm
A current balance is constructed as follows: part of a wire, 10.0 cm long, is placed on a plate of an electronic balance, as shown in the figure below. This wire is connected to a current source (power supply) and a long horizontal wire, parallel to the wire on the platter, positioned just above it. The distance between the central axis of the two wires is 2.00 cm. When the source is turned on, the scale reading increases by 7.00 mg. What is the current in the wire (at A)? If the sensitivity of the balance is 0.100 mg, what is the minimum current that can be detected (in mA to one decimal place)?