You have available a 550 watts pump with 70% efficiency. Is it possible to use this pump to transfer 10 m3/hr of a liquid through a 0.047 m inside diameter pipe, from one open tank to another, if the liquid is discharged at a point 10 m above the liquid level in the suction tank and the total friction losses are 50 J/kg? The density of the liquid is 1050 kg/m3 and the viscosity is 2 cP.

You have available a 550 watts pump with 70% efficiency. Is it possible to use this pump to transfer 10 m3/hr of a liquid through a 0.047 m inside diameter pipe, from one open tank to another, if the liquid is discharged at a point 10 m above the liquid level in the suction tank and the total friction losses are 50 J/kg? The density of the liquid is 1050 kg/m3 and the viscosity is 2 cP.

Similar questions

Please state all assumptions
A tank in the shape of an inverted cone has a height of 20 meters and a base radius of 11 meters and is filled with liquid to a depth of 16 meters. Determine the amount of work needed to pump all of the liquid to a point 1m from to the top of the tank. Assume that the density of the liquid is 793 kg/m 3
AST Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y 12.5 cm below point 1. The water pressure at point 1 is 3.20 x 10 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s (b) point 2 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s
Verify that work input equals work output for a hydraulic system assuming no losses due to friction. Do this by showing that the distance the output force moves is reduced by the same factor that the output force is increased. Assume the volume of the fluid is constant. What effect would friction within the fluid and between components in the system have on the output force? How would this depend on whether or not the fluid is moving?
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.700 L/s, with an output pressure of 2.00 x 105 N/m². You may neglect frictional losses in both parts of this problem. (a) The water enters a hose with a 3.00 cm inside diameter and rises 3.00 m above the pump. What is its pressure (in N/m²) at this point? N/m² (b) The hose goes over the foundation wall, losing 1.70 m in height, and widens to 4.00 cm diameter. What is the pressure now (in N/m²)? N/m²
Water flows at 1 m/s from a hot water heater, through a 410 kPa pressure regulator. The pressure in the pipe supplying an upstairs bathtub 3 m above the heater is 350 kPa. What’s the speed in this upstairs pipe? (Numerical answer is assumed to be in m/s)
What flows at 0.850 m/s from a hot water heater, through a pressure regulatory at 450 kPa on the ground floor of the house. This same pipe is used to supply water to a bathtub 3.7 m higher in the household at a pressure of 414 kPa. What is the flow speed in the pipe on the same floor as the bathtub?
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.75 L/s, with an output pressure of 1.5×10^5 Pa. (a) The water enters a hose with a 2.8 cm inside diameter and rises 2.2 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.55 m in height, and widens to 6.6 cm in diameter. What is the pressure now? You may neglect frictional losses in both parts of the problem.
7. A fuel oil tank is an upright cylinder, with radius 3 meters and height 13 meters. a. Assuming the tank is full, calculate the work required to pump the oil out a spout 1 meter above the top of the tank. Round to the nearest whole number, and include units with your answer. Note: W - Vpgd Density of the oil = 800 kg/m³. Acceleration due to gravity = 9.82 b. Is it true that it takes half as much work to pump the oil out of the tank if it's only half full? Explain why or why not.