You have 4 acre of watermelons that you irrigate. The irrigation system you use under standard pressure of 35 psi has a flow rate of 105 gpm. The nozzle sprays a circular area with a radius of 24 feet. a. How many square feet are in the water- melon patch? b. What is the area covered by one nozzle? c. How many nozzles are needed?

You have 4 acre of watermelons that you irrigate. The irrigation system you use under standard pressure of 35 psi has a flow rate of 105 gpm. The nozzle sprays a circular area with a radius of 24 feet. a. How many square feet are in the water- melon patch? b. What is the area covered by one nozzle? c. How many nozzles are needed?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A sand cone equipment is used to perform a field density test on a compacted earthfill. Weight of…

Q: Q2/ Sprinkler irrigation system irrigate 8 ha farm in 2 hours with average sprinkler irrigation rate…

A: To solve the given problem, we need to follow these steps:Determine the time when water starts to…

Q: 1. A 52-inch diameter transmission pipe carries 3,000 gallons per minute from an elevated storage…

Q: Disinfection, sedimentation, flocculation, coagulation, and filtration are processes for a surface…

A: Coagulation is defined as a water treatment process in which chemicals which are known as coagulants…

Q: Problem 1.12 (modified), Masters and Ela, Introduction to Environmental Engineering and Science, 3rd…

A: Given Flow rate 2.5 MGDBOD 12 mg/LVolume of 1st 6.5 MGVolume of 2nd 3.5 MGConstant 0.43/dayTo find…

Q: The Wood family and the Davis family each used their sprinklers last summer. The water output rate…

A: Given: Water output: W1 = 40 L/hr W2 = 30 L/hr Total output = 1850 L Total consumed hours = 50 hrs…

Q: Problem 3: You are considering three design alternatives for treating a pollutant in wastewater…

Q: he pump shown in the figure adds 15 ft of head to the water being pumped when the flow rate is 1.5…

A: Diameter of pipe, Length of pipe, Pressure at A,

Q: PROBLEM 3 An 85-percent-efficlent pump is used to Increase the pressure of water in a 10-cm-diameter…

A: To find out the A) Head Added by pump. B) Required horse power of the pump for discharges 0.015…

Q: Hoover Dam www. Lake Mead Las Vegas Colorado River 15 Jean CALIFO Primm ORNIA Henderson Boulder City…

A: Given data- Intake elevation h1=1170 feet above sea level, Reservoir elevation h2=2030 feet above…

Q: The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor…

Q: Problem 3: You are considering three design alternatives for treating a pollutant in wastewater…

A: Given data, Q = 8.6 mgd = 8.6×10^6 gal/d V = 9000 gal. For each system K= 1.1/min for first order =…

Q: Cooling water for a chemical plant must be pumped from a river 2,500 ft from the plant site. A…

Question

You have 4 acre of watermelons that
you irrigate. The irrigation system you use
under standard pressure of 35 psi has a
flow rate of 105 gpm. The nozzle
sprays a circular area with a radius of
24 feet.
a. How many square feet are in the water-
melon patch?
b. What is the area covered by one nozzle?
c. How many nozzles are needed?
d. What is the flow rate when all the nozzles
are used?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

VIEW

Step 2 area covered by one nozzle

VIEW

Step 3 Number of Nozzles required

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the water distribution system given below, find the discharge at each pipe. The roughness for all pipes is 0.02. Pipe Diameter Length El. = 126 m (m) (cm) 15 350 El. = 109 m AJ BJ CJ 10 200 10 250 -11-1 A El. = 100 m
The Flames Pool Company (FPC) was hired to drain a swimming pool when it is raining outside. If it is raining at a rate of 2 inches/hour and the flat swimming pool bottom surface area is 2000 ft2 answer the following two questions: What pump capacity in gallons/minute (gpm) must FPC use to keep the rain water accumulating in the swimming pool at a constant rate? What pump capacity in gpm must FPC use to reduce the rain water accumulation in the swimming pool at a rate of 4 inches/hour.
Please provide the right answer to this problem. Show all of your work, please.
Minor Losses A pipe system is comprised of a flush entrance, one gate valve, one 90° elbow, one 45° bend, and a globe valve. If the fluid flows at 11 ft/s, what is the head loss due to minor losses? O 12.4 ft O 14.3 ft O 22.5 ft 13.2 ft O 8.55 ft O 6.60 ft
A groundwater supply has been designated as vulnerable to fecal contamination, and the state has specified a disinfection level of 99.99% (4.0-log) virus inactivation. The peak hourly pumping rate is 2000 gpm from the well field through a 4200-ft pipe with a 16-in diameter to a reservoir in the town. The water temperature is 10°C. A. what is the contact time in the pipeline? B. What chlorine residual is required in the water at the outlet of the pipeline? F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 %23 & 3 4 7 8 T Y D F G K CO LLI
CIVIL ENGINEERING (Drainage): Two seperated dry stormwater ponds with the same elevation at the bottom are connected by two pipes (RCP 18'') laid flat. Suddenly, there is a difference in the ponds' water levels. What could be a reason for this and how can you fix it?
Hello can you answer this question for me? All the info you need to answer the question is here. Thamnk you A salt lake doesn't have an outflow since evaporation totally balances the intake flow. This is the salt content of the lake is 52g/L, the volume of the lake 2.5 x 1011 m3 The lake's intake (of salt) stream has a 0.18 g/L concentration and moves at a pace of 3.7 x 109 m3/yr. How long ago did the outflow halt if the lake's concentration was 0.18 g/L at the start?
The width of the channel is reduced in the downstream. Upstream flow is subcritical. Please can you explain possible changes to the flow of the channel, and show how this would look on the specific energy diagram? Thanks for any help! Ive attached a picture of the specific energy diagram.
Q avg = 0.181 m^3/s
Determine the dimensions of a high rate trickling filter for the following data: (ii) Recirculation ratio = 1.5 (iv) BOD removed in primary tank = 25%. (i) Sewage flow = 3.0 MLD (iii) BOD of raw sewage = 250 mg/L (v) Final effluent BOD desired = 30 mg/L By what % the diameter of the filter will have to be modified if it is to be designed as a standard rate trickling filter for the above requirement.
As the project engineer for your consulting firm, you are in charge of designing a flocculation tank to treat municipal drinking water. The design flow for the plant is 0.050 m3/s. The average water temperature is 10oC. The following design assumptions for the flocculation basin have been made:Number of tanks = 1Number of compartments in tank: 3Tapered G in 3 compartments: 60, 50, and 20 s-1Detention time = 30 min for entire flocculation basinDepth = 3 mTanks will have a square compartment plan (overhead) view1 Horizontal shaft paddle wheel per axis will be usedPaddle wheels will have 4 arms and 2 blades/armPaddle blades are 3 m long by 0.6 m wide. Assume blade spacing (diameter) of 1 and 2 m. Design the flocculation tank by providing the following for the first two compartments only:a) Tank and compartment dimensions in mb) Water power input in kWc) Rotational speed of the paddle wheel shaft in rpm
4/2 Determine the force in each member of the loaded truss. A 30⁰ 60° k B 400 kg