Determine the dimensions of a high rate trickling filter for the following data: (ii) Recirculation ratio = 1.5 (iv) BOD removed in primary tank = 25%. (i) Sewage flow = 3.0 MLD (iii) BOD of raw sewage = 250 mg/L (v) Final effluent BOD desired = 30 mg/L By what % the diameter of the filter will have to be modified if it is to be designed as a standard rate trickling filter for the above requirement.

Determine the dimensions of a high rate trickling filter for the following data: (ii) Recirculation ratio = 1.5 (iv) BOD removed in primary tank = 25%. (i) Sewage flow = 3.0 MLD (iii) BOD of raw sewage = 250 mg/L (v) Final effluent BOD desired = 30 mg/L By what % the diameter of the filter will have to be modified if it is to be designed as a standard rate trickling filter for the above requirement.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. After your flash mix the water was sent to a clarification basin that was 24 feet in diameter and 20 feet tall. What was the detention time in hours of 0.43 MGD? 5.4 hours 4.3 hours 3.8 hours 2.3 hours After the water leaves your sedimentation basin, it is ready for filtration. Your two filters measure 10 feet in diameter. What is the filtration rate is gpm for your flow of 0.43 MGD? 19 gpm/sq/ft 29 gpm/sq/ft 39 gpm/sq/ft 49 gpm/sq/ft You have had a filtration breakthrough (failure) and have brought your old roughing filtration system on line. The old filter is 8 feet square and 4 feet deep. What is the filtration rate in gpm/sq/ft for your flow of 0.43 MGD? 10.33 gpm/sq/ft 8.55 gpm/sq/ft 5.99 gpm/sq/ft 4.66 gpm/sq/ft
An effluent at flow rate of 2760 m3/day is to be treated. The dosage of chlorine is 15 mg/lt and the disinfction model is Nt=Noe-0.145t. Determine the volume of disinfection unit required to kill 98% microbes.
A contaminant is present in an industrial wastewater at a concentration of 268 mg/L and can be degraded according to a first-order reaction. Previous research has identified that K contaminant is regulated at 2.5 mg/L and must be removed prior to discharge to the sewer. 1. 5.2/hr. The a. Identify the required reaction time (in hours) to degrade the contaminant to the target effluent concentration of 2.5 mg/L in an ideal continuously-stirred tank reactor (CSTR). b. Identify the required reaction time (in hours) to degrade the contaminant to the target effluent concentration of 2.5 mg/L in an ideal plug flow reactor (PFR). If the wastewater flowrate is 7,000 gallons/day (gpd), identify the volume required (in gallons and ft') for ideal CSTR and PFR treatment system to achieve the target effluent concentration of 2.5 mg/L. d. Management would like to use two 500 gallon tanks operated as two-CSTRS in series to treat the wastewater at a flowrate of 7,000 (gpd). Will this be satisfactory for…
Determine how much extra volume is needed to treat the following wastewater in a CSTR than in a plug flow reactor. • Influent TOC: 273 mg/L • Required Effluent TOC: 57.0 mg/L • Flow: 792,500 gallons/day • First Order Microbiological Rate Coefficient (k’): 5.98/day Answer: 295,000 gallons 2. Discuss in detail at least two ways the k’ value may have been obtained and which technique is probably more accurate?
Problem: 1. Design a facultative pond to treat (10650)gpm of sewage having (10650/20)mg/L of BOD. The average summer and winter temperature is 43°C and 13°C, respectively. Convert the same pond into aerated lagoon, if the concentration of influent BOD reaches to (10650)mg/L. 2. Determine the diameter of a trickling filter for a wastewater flowing at the rate of (10650)m³/day. The influent BOD (S.) concentration for the wastewater is (10650 * 10)mg/L, whereas desirable effluent BOD should be as per NEQS.
i). A town produces 8 million litre of sewage per day. BOD of sewage is 260 mg/L, it is to be discharged into a river flowing at a rate of 0.2 m³/s and it's BOD is 5 mg/L. Find out the BOD of river after mixing? [Assume mixing is instantaneous]
Q1: Design a lowrate trickling filter for treating a municipal wastewater if the effluent BOD is 16.5 g/m³ , influent BOD is 88 g/m³ and the flowrate of the sewage is 16.2 L/s. Take C=5.4, filter depth= 1.5m?
Seatwork No. 4 A residential area of a city has a population density of 15000 per km2 and an area of 1800000 m2. If the average sewage flow is 225 L/cap-day. Use the maximum sewage flow in the design which has 50% increase from the average flow. The Infiltration rate is 0.055 cu.m. per second and the consider leakage of 0.025 cu.m. per second. Estimate the maximum rate of flow in m3/s. Seatwork No. 5 The present population is 28,000 and the average water consumption is 16,000,000 L/day. If the Maximum sewage flow is 225 L/cap-day and the Infiltration rate is 0.055 cu.m. per second and the leakage of 0.025 cu.m. per second. Use the population data for year 2000 is 10000. Estimate the maximum rate of flow in m3/s after 5 years.
As an operator of a wastewater treatment facility, you have learned that your plant runs well at an SRT (based on MLVSS (X) in the aeration basin) of 12 days. If today’s MLVSS (X) concentration is 2,700 mg/L and the RAS (Xr) concentration is 5,500 mg/L, how many L of sludge should you waste from the secondary clarifier today? Other design conditions: Average influent flow = 12,000 m3/d Influent soluble BOD = 150 mg/L Required effluent TSS = 30 mg/L Aeration tank Volume = 1,000 m3
It is proposed to use a high rate two stage trickling filters when the following data is given: The plant will recieve daily 5 MLD of sewage with a BOD of 260 ppm BOD loading in the raw sewage Oper hectare metre = 10000 kg/day In both cases, recirculation ratio = 1 Total filtering media is to be divided between the two filters with 1 m depth The expected BOD of the plant effluent will be mg/l