You are riding your bicycle down the street at a speed of 16 m/s. Your bicycle's frame has a mass of 6.0 kg, and each of its two wheels has mass 2.2 kg and radius 0.34 m. Each wheel can be thought of as a hollow hoop (assuming that the rim has much larger mass than the spokes). What is the total kinetic energy of the bicycle (in Joules)?(take into account both the translational and rotational motion.)

You are riding your bicycle down the street at a speed of 16 m/s. Your bicycle's frame has a mass of 6.0 kg, and each of its two wheels has mass 2.2 kg and radius 0.34 m. Each wheel can be thought of as a hollow hoop (assuming that the rim has much larger mass than the spokes). What is the total kinetic energy of the bicycle (in Joules)?(take into account both the translational and rotational motion.)

Similar questions

In the figure, three 0.10 kg particles have been glued to a rod of length L = 11 cm and negligible mass and can rotate around a perpendicular axis through point O at one end. How much work is required to change the rotational rate (a) from 0 to 20.0 rad/s, (b) from 20.0 rad/s to 40.0 rad/s, and (c) from 40.0 rad/s to 60.0 rad/s? (d) What is the slope of a plot of the assembly's kinetic energy (in joules) versus the square of its rotation rate (in radians-squared per second-squared)? Axis -P--P-- P- (a) Number i Units (b) Number i Units (c) Number i Units (d) Number i Units
A 34 kg hoop of radius 1.3 m, initially rotating at 301 revolutions per minute, is brought smoothly to a stop in 20 s. What is the average power (in Watts) associated with the force that brings the hoop to a stop?
A solid ball of mass 0.10 kg and radius 2.8 cm is released from rest on a no-slip surface at a height of 0.75 m above the bottom of the track, as shown. After reaching its lowest point, the ball begins to rise again, this time on a frictionless surface. Find: a) the ball's angular speed when it is on the frictionless side of the track and b) the height ball rises on the w = 120 rad/s; h = 0.54 m frictionless side.
A car is designed to get its energy from a rotating flywheel (solid disk) with a radius of 2.00 m and a mass of 400 kg. Before a trip, the flywheel is attached to an electric motor, which brings the flywheel's rotational speed up to 4500 rev/min. (a) Find the kinetic energy stored in the flywheel. (b) If the flywheel is to supply energy to the car as would a 20.0-hp motor, find the length of time the car could run before the flywheel would have to be brought back up to speed.
a 40kg disk with a radius of 30 cm is spinning around a fixed vertical axis with an angular speed of 10 rad/s. How much work must be done on the disk to bring it to an angular speed of 20 rad/s? a)270J 200J 150J 100J e)40J
Two hangers are attached by a string to a vertically mounted pulley system as shown. One disk is bigger than the other, and the disks are attached to each other such that they rotate together. The axle has negligible friction. The mass of the large disk is 1200 grams and the radius is 11 cm. The mass of the small disk is 400 grams and the radius is 4 cm. The high hanger has a mass of 200 grams and starts 80 cm above the ground. The lower mass starts on the ground and has a mass of 100 grams. The hangers are released from rest. What is the velocity of the 200 gram hanger when it hits the floor?
A solid, uniform disk of radius 0.250 m and mass 49.0 kg rolls down a ramp of length 3.80 m that makes an angle of 12.0° with the horizontal. The disk starts from rest from the top of the ramp. (a) Find the speed of the disk's center of mass when it reaches the bottom of the ramp. m/s (b) Find the angular speed of the disk at the bottom of the ramp. rad/s
A frictionless pulley has the shape of a uniform solid disk of mass 2.90 kg and radius 10 cm. A 1.30 kg stone is attached to a very light wire that is wrapped around the rim of the pulley (the figure (Figure 1)), and the system is released from rest. How far must the stone fall so that the pulley has 3.40 J of kinetic energy? What percent of the total kinetic energy does the pulley have?
A 51 kg hoop of radius 1.3 m, initially rotating at 481 revolutions per minute, is brought smoothly to a stop in 12 s. What is the average power (in Watts) associated with the force that brings the hoop to a stop?
A 2.00-m long rod is hinged at one end. The rod is initially held in the horizontal position, and then released as the free end is allowed to fall. (a) What is the angular acceleration as it is released? (b) What is the angular acceleration when it reaches the vertical position? (c) Which position has the maximum angular velocity (vertical or horizontal)? (d) Which position has the maximum angular acceleration (vertical or horizontal)? (The moment of inertia of a rod about one end is ML2/3.)
The figure shows a uniform disk that can rotate around its center like a merry-go-round. The disk has a radius of 2.3 cm and a mass of 19 grams and is initially at rest. Starting at time t= 0, two forces are to be applied tangentially to the rim as indicated, so that at time t = 1.3 s the disk has an angular velocity of 200 rad/s counterclockwise. Force F, has a magnitude of 0.100 N. What is magnitude F2? Number i Units eTextbook and Media Hint GO Tutorial tv DII DD 888 F12 F10 F11 E7 F8 F9 F6 F4 F5 F1 F2 F3 ) 1 & 23 2$ 4 6 7 8 9. 3 { Q W E Y H K ...- * CO