A solid ball of mass 0.10 kg and radius 2.8 cm is released from rest on ano-slip surface at a height of 0.75 m above the bottom of the track, asshown. After reaching its lowest point, the ball begins to rise again, thistime on a frictionless surface. Find: a) the ball's angular speed when it ison the frictionless side of the track and b) the height ball rises on thew = 120 rad/s; h = 0.54 mfrictionless side.

The speed of an object that moves in a circular orbit is known as angular speed. Angular speed is…

Answered: A solid ball of mass 0.10 kg and radius…

Similar questions

What is the total kinetic energy of a spherical shell with a mass of 7.4 kg and radius of 23 cm rolling without slipping on a horizontal floor at a speed of 6.8 m/s? (in 3) A: 114 OB 171 OC: 285 OD: 2.16-10 OE 2.33×10 Submit Anwwer Tries 0/5 Post Discussion Send Feedback
Suppose a 175 kg motorcycle is heading toward a hill at a speed of 34 m/s. The two wheels weigh 12 kg each and are each annular rings with an inner radius of 0.280 m and an outer radius of 0.330 m. a) how high can it coast up the hill, if you neglect friction in m? b) how much energy is lost to friction if the motorcycle only gains an altitude of 39m before coming to rest?
Three point masses ma, mB and mc are located in the x-y plane at points A, B and C as shown in Figure They are connected together by massless rods. Find the kinetic energy of the system if it rotates with an angular speed of 4.0 rad/s about the z-axis passing through point A. Fig# y mg = 0.10 kg 0.30 m 0.40 m A m, = 0.30 kg mc = 0.20 kg A) 0.46 J В) 0.69 J C) 0.21 J D) 1.2 J E) 2.5 J
Pls answer with handwritten solutions
Assume the earth to be a sphere of uniform density (a) What is its rotational kinetic energy? Take the radius of the Earth to be 6.4 x 103 km and the mass of the Earth to be 6.0 x 1024 kg. (b) Suppose this energy could be harnessed for our use. For how long could the Earth supply 1kW of power to each of the 4.2 x 109 persons on Earth.
The figure below shows a ball with mass m = 0.322 kg attached to the end of a thin rod with length L = 0.454 m and negligible mass. The other end of the rod is pivoted so that the ball can move in a vertical circle. The rod is held horizontally as shown and then given enough of a downward push to cause the ball to swing down and around and just reach the vertically up position, with zero speed there. (a) What initial speed must be given the ball so that it reaches the vertically upward position with zero speed? m/s (b) What then is its speed at the lowest point? m/s (c) What then is its speed at the point on the right level with the initial point? m/s
The puck in the figure below has a mass of 0.186 kg. Its original distance from the center of rotation is 40.0 cm, and it moves with a speed of 85.0 cm/s. The string is pulled downward 15.0 cm through the hole in the frictionless table. Determine the work done on the puck. Hint: Consider the change in kinetic energy of the puck. Need Help? Read It Watch It
Problem 9: A solid ball with mass, M=2.5 kg and radius, R=0.2 meter is released from rest from the top of an incline of height, h=3.5 meter. Ignore any energy loss due to friction or air drag. Consider g=9.8 m/s2. (a) The linear speed of the ball at the bottom is ________ (b) The rotational kinetic energy of the ball at the bottom is _________
A table is composed of a normal area and a sticky area. A disc has thickness d, radius R and made of a material of density p. The disc rolls on the normal area with translational velocity v without loss of energy. Then, the disc enters the sticky area and consequently immediately starts rolling and stops rolling after rolling the total distance l in the sticky area. Find the work done during this process.
A disk of radius = 2.02 mm is attached to a high-speed drill at a dentist’s office and is turning at 96,185 rad/sec. Determine the tangential speed of a point on the outer edge of this disk. Use g=9.8
A thin uniform rod AB of length L and mass m is nailed to a wall through point C, which lies on the rod at the distance L/4 from point A. Assume that the rod rotates frictionlessly about the nail. Initially the rod is kept horizontal,and it is then released (a) Find the angular acceleration of the rod right after it has been released (b) find the total kinetic energy of the rod at the moment when it was vertical
Suppose you had a machine for 100% efficiently transferring kinetic energy of a rotating bicycle pedal to electrical energy. If the mass of a pedal is 200 g, (a) how fast must the pedal be moving to power a 17.00 W LED light? (b) what is the angular speed, in rpm, if the distance from the centre of the crank to the pedal is 16 cm?

SEE MORE QUESTIONS