Yo T M M PROBLEM 8.5-9

Q: A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as…

A:

Q: 3 m 30° 30°

A: The uniform temperature rise in bar 1 is .The modulus of elasticity is .The area given is .The…

Q: A cylinder filled with oil is under pressurefrom a piston, as shown in the figure. The diameter dof…

A: Given   Shear stress = 5500 psi          Load, F = 3500 lb   Diameter, d = 1.80 in Find   Thickness,…

Q: A flexible connection consisting of rubber pads(thickness t =9 mm) bonded to steel plates is shown…

A: Given   Force P =16 kN Shear modulus for the rubber is G = 1250 kPa Thickness t =9 mm Find…

Q: A circular tube of inner radius r1 and outer radius r2 is subjected to a torque produced by forces P…

A: a-calculate the r2 the minimum permissible outer radius of the tube given…

Q: The constructed shear force diagram (SFD) for the simply supported beam with a Triangle distributed…

A: To find: (a) The reaction at the supports. (b) The shear force at supports. (c) The value of x. Free…

Q: A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum…

A:

Q: The hollow drill pipe for an oil well (see figure)is 6.2 in. in outer diameter and 0.75 in. in…

A: Given Outer diameter = 6.2 in Thickness = 0.75 in Weight = 62 kips Torque = 185 kip-in To find…

Q: 2.6-2 A circular steel rod of diameter dis subjected to a tensile force P = 3.5 kN (see figure). The…

A:

Q: Q.3) For the shaft consist of two parts shown in figure. If shaft (1) has outside diameter doutl =…

A:

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: A circular post, a rectangular post, and a post of cruciform cross section are each compressed by…

A: Given: Diameter and the depth of rectangular and cruciform post=d Load acting at corner of the each…

Q: One side of a petrol drill pipe, as shown in the figure, has been lifted with the use of a crane P…

A: (a) The cross-sectional diagram of the pipe is shown below.

Q: 0.4 m y 0.2 m 0.3 m 0.6 m 5 m EFG kirişinin enine kesiti В 0.25 m 1200 N Q2) As shown in the figure,…

A: Given: The width of the cross-section, b = 25 mm The height of the cross-section, h = 50 mm The…

Q: Cable DB supports canopy beam OABCas shown in the figure. Find the required cross-sectionalarea of…

A: Draw a diagram for the problem. Here, T is the tension in the cable, θ is the angle made by the…

Q: A cantilevered structure has dimensions L=65-in, L-9.5-in, L=6.2-in, LF3.8-in and diameter d=2.5-in.…

A: Given L1 = 65 in L2= 9.5 in L3 = 6.2 in  L4 = 3.8 in  d1 = 2.5 in Fy = 78 lb Fz = 153 lb We have to…

Q: For the pressure vessel in which the loading condition is seen in the figure determine the maximum…

A: Note: the stress values are calculated for the point “a” on the top of the cylindrical pressure…

Q: A gondola on a ski lift is supported by twobent arms, as shown in the figure. Each arm is offsetby…

A: given; allowable tensile stress (σ)=100MPashear stress(τ)=50MPaweight(W)=12KN…

Q: A thin-walled circular tube and a solid circular bar of the same material (see figure) are subjected…

A:

Q: A high-strength steel bar used in a large cranehas a diameter d = 2.00 in. (see figure). The steel…

A:

Q: Problem No. 2. A 150-mm-wide steel bar with a butt-welded joint, as shown. SET LOAD P NORMAL STRESS…

A: Given DataP=205kNσn=80MPaτ=40MPaθ=57{taken} C section taken for computing the minimum thickness

Q: A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is held against…

A: Outside diameter = 50 mm Inside diameter = 40 mm Shear stress = 55 Mpa

Q: A full quarter-circular fillet is used atthe shoulder of a stepped shaft having diameterD2 =1.0 in.…

A: Diameter of step 2 D2 = 1 in Applied torque T =500 lb-in let the maximum shear stress at the stress…

Q: A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 5.1 in. is…

A: Given:Length of the pipe, L=5 ftOutside diameter, d2=9.3 inInside diameter, d1=5.1 inAxial force,…

Q: The articular Cartilage is subjected to plane stress with normal stresses &x ,Oy and shear stress…

A:

Q: A steel wire (E = 200 GPa) of a diameterd = 1.25 mm is bent around a pulley of a radiusR0 = 500 mm…

A: Simple stress is often called direct stress because it develops under direct loading conditions,…

Q: A cantilever steel beam with the triangular cross section is loaded with the concentrated force as…

A:

Q: L 10 kN 7 kN 14 kN H 240 mm The pipe in the figue problem is subjected to the forces given in the…

A: Given: The load acting on pipe along y-axis, Py = 10 kN The load acting on pipe along x-axis, Px =…

Q: (1) A cantilever steel beam with the triangular cross section is loaded with the concentrated force…

A: Given:To find:Stress state at point M.

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 120 mm…

A: The given values are - Dimensions 120×45×43 mm3Poisson's Ratio μ= 0.3E= 140 GPa=140×103 MNm2 Tensile…

Q: A pressurized cylindrical tank with flat endsis loaded by torques T and tensile forces P (see…

A: Given data as per question The internal pressure p = 7.25 MPa  Torque T =850 N .m. t = 6.5 mm

Q: A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 165 kN, acting as…

A:

Q: At an arbitrary cross-section, a - a the state of stress is obtained at various points (point 1 ~ 5,…

A:

Q: For the truss shown below, use symmetry to determine the displacement of the and the stresses in…

A:

Q: ..For the figure shown blow, if the temperature decrease by 40°C. find the stress in the Aluminuim…

A:

Q: A car weighing 130 kN when fully loadedis pulled slowly up a steep inclined track by asteel cable…

A:

Q: x = A cylindrical rod is made of three segments and is subjected to axial loads as indicated in the…

A: Basic concept used for tension and compression,If a force is acting away from the section, it will…

Q: Hi, can you please show me how to solve this problem? Thank you!

A: The objective of this problem is to determine the maximum tensile stress, maximum compressive…

Q: A short column with a wide-flange shape is subjected to a compressive load that produces a resultant…

A:

Q: The articular Cartilage is subjected to plane stress with normal stresses o , Oy and shear stress…

A: This problem can be simply solved by evaluating the normal stress in y-direction and shear stress…

Q: In the beam loading system given below, A is a simple and C is a sliding support. The outer diameter…

A:

Q: A cantilever beam with a width b =100 mmand depth h = 150 mm has a length L =2 m and issubjected to…

A: Equation of Pure Bending:- σy=MI=ER where     M=Bending Moment                σ=Bending stress at a…

Q: the principal stresses at a point H on the surface of the vessel and the absolute maximur shear…

A:

Q: A beam of T-section is supported and loaded as shown in the figure below. The cross section has…

A:

Q: The articular Cartilage is subjected to plane stress with normal stresses ox , o, and shear stress…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.