یا #I A A 3m 600 | 3m B 4m D 3m 5m B, C, and I are pin connected Note: E to C is one member ( Determine: Support reactions at E and A

Q: SITUATION 3 Determine the height of the infinite slope, H, such that the factor of safety of 3.1 is…

A: Slope - Infinite The factor of safety, FOS = 3.1 The angle of slope with respect to horizontal, β =…

Q: The angular section shown is subjected to a load of 400 kN and is connected. to the column with 6-22…

A: Answer  we are given Pa = 400 KN number of bolts n = 6 diameter of bolt = 22 mm allowable tensile…

Q: D 5m B -5 m- -5 m- а. Determine the maximum positive ordinate for member DC. Determine the location…

A:

Q: Determine the moments of inertia of the Z-section about its centroidal xo- and yo-axes. 23 mm…

A:

Q: An electrical worker stands in the bucket that hangs from a pin at end D of the boom of the cherry…

A: To find internal force at point E

Q: At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is…

A: Total elongation is given by ; δ1 + δ2 = 0.04 (gap) where ; δ = α×∆T×L α1L1∆T + α2L2∆T = 0.04 ∆T…

Q: Replace the three forces with an equivalent force-couple system, with the force acting at O. 280 N…

A: To find equivalent couple force system action at O

Q: A load of P = 86 kN is supported by a structure consisting of rigid bar ABC, two identical solid…

A:

Q: 2) A beam loaded with both transverse and longitudinal loads as show. his beam loading is typical of…

A:

Q: Determine the resultant of the concurrent forces; F1 = 4000lb upward to the left with an angle 40°…

A: Given Data Determine the resultant of the concurrent forces.

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: Given Data  TC = 19400 Nm = 19400 × 103 Nmm  Allowable shear stress in brass = 53 MPa Allowable…

Q: At an axial load of 22 kN, a 15-mm-thick x 50-mm-wide polyimide polymer bar elongates 3.5 mm while…

A:

Q: Please

A:

Q: A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi;…

A:

Q: The length of a belt in an open-belt drive, L, is given by: where and L = √4c² −(D−d)² + ¹/{D®₂…

A: Newton-Raphson Method: Newton-Raphson method is also known as the Newton method. It is the most…

Q: It is required to determine the vertical angle of the rod that is above the theodolite instrument.…

A: Given Inclined distance = 55m Vertical distance = 45 m Required Vertical angle and horizontal…

Q: A solid circular steel shaft having an outside diameter of 2.00 in. is subjected to a pure torque of…

A: For each section, the angle of twist is calculated as TL/JG. When the twists of the individual…

Q: Q3. A vertical curve is to be designed to join gradients of -2 and -4% with the design speed of…

A: Stationing of PVI = 200+10 Elevation of PVI = 120ft Initial Grade G1 = -2% = b Final Grade G2 = -4%…

Q: The 2.6 kN force shown in the figure is the resultant of the two forces P and Q. Determine the…

A: Given data in question Resultant 2.6 kN Angles To find out  Value of P and Q

Q: At an axial load of 26 kN, a 35-mm-wide by 15-mm-thick polyimide polymer bar elongates 2.9 mm while…

A: Answer  (a) We know that Modulus of Elasticity is given by E = σε σ = stress σ = loadArea…

Q: Two sides of a triangle are 50m and 60m long. The angle included in between these sides is 30…

A:

Q: A 40-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

A:

Q: 780 MPa; v = 0.46] rod has a diameter of 90 mm before lo d must not exceed 92 mm when loaded. What…

A: Given data -  Young's modulus (E) = 780Mpa  Poisson's ratio (v) = 0.46  Diameter of rod (d) = 90 mm…

Q: A hollow steel [G= 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…

A: Given,    G = 12000 ksi     Outside diameter, do = 3.5 in     Torque, T = 3170 lb-ft     Permissible…

Q: 1. I. For the truss below, compute for the support reactions. Also, compute for all member forces.…

A:

Q: A solid 1.08-in.-diameter steel [G = 9000 ksi] shaft is subjected to the torques shown. Determine…

A:

Q: Using the method of sections, answer the problem below: Indicate all zero force members and…

A: A truss is given.  The truss is externally determinate. Therefore the support reactions can be…

Q: 1. Replace the beam in the figure by a wide flange. The allowable flexural stress of the structural…

A:

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 202 mm and a…

A:

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A: Given Data External diameter of shaft-1 (D1) = 3.95 in.  External diameter of shaft-2 (D2) = 2.1…

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A: Given data: T A= 110 N-m T B= 332 N-m T C= 396 N-m T D= 174 N-m Internal torque in segment 1 : Ta =…

Q: Four forces of act on a system as shown in the figure. Determine (a) the magnitude and direction of…

A: System of four forces are given below:To find:-(a) Magnitude and direction of resultant force(b)…

Q: In the two-member assembly shown, find the axial force in rod (1) if P = 14.0 kips. 8 ft O 11.39…

A:

Q: At the proportional limit, a 20-mm-thick x 75-mm-wide bar elongates 5.4 mm under an axial load of…

A: Given data in question  Load 525 kN Length 1.6 m Poissons ratio 0.32  Cross section 20×75 mm To find…

Q: ..The correct distance between two points is 220.45m. Using a 100m tape that is "x" m too long, the…

A: