X = 4 km If aquifer hydraulic gradient, hydraulic conductivity and effective porosity are found to be 0.4, 0.5 m/day and 0.2 respectively, determine how long the contaminants have been in the aquifer (in years)? 1 year = 365 days

X = 4 km If aquifer hydraulic gradient, hydraulic conductivity and effective porosity are found to be 0.4, 0.5 m/day and 0.2 respectively, determine how long the contaminants have been in the aquifer (in years)? 1 year = 365 days

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem G: For Problem 27 to 28. In a constant head permeability test the following are given L= 250 mm and A=105 cm?. If the value of k = 0.014 cm/secand flow rate of 120 cm3/min which is to be maintained. 27) What is the head difference, h in the specimen? b) 34.341 cm 28) Determine the discharge velocity in cm/sec? b) 0.109 a)34.136 cm c) 33.901 cm d) 34.014 cm a) 0.0189 c) 1.019X102 d) 0.019
A pumping test in an aquifer has yielded the following data: A pumping well with a diameter of 15 cm pumps at a rate of 12 m³/day, and draws the aquifer down by 3.6 m. Drawdown at a monitoring well 20 m away is 1.1 m. a) Calculate the Transmissivity of the aquifer. Assume this number is representative of the entire aquifer. b) Determine saturated hydraulic conductivity, and identify a soil type from table 7.2 in the Margulis book. The aquifer thickness is 20 m. ●
An unconfined aquifer is 10 m thick and is being pumped so that one observation well placed at a distance 76 m shows a drawdown of 0.5 m. On the opposite side of the extraction well is another observation well 100 m from the extraction well, shows a drawdown of 0.3 m. Assume the coefficient of permeability of 50 m/day. a.) What is the discharge f the extraction well? b.) Suppose the well at 100 m from the extraction well is now pumped. Show with a sketch what this will do to the drawdown. c.) Suppose the aquifer sits on an aquaclude that has a slope of 1/100. Show with a sketch what this will do to the drawdown.
Q-7 Water table of an aquifer drops by 100 cm over an area of 1000 km². The porosity and specific retention of the aquifer material are 25% and 5%, respectively. The amount of water (expressed in km³) drained out from the area is.
1. A piezometer point is 35 m above mean sea level. The fluid pressure in the aquifer at that point is 6.70 x 10E+6 N/m2. The aquifer has fresh water at a temperature of 15 degree C. a) What is the point water pressure head? b) What is the total head?
Compute the average porosity for given reservoir depicted in Fig. Q3(d) using relevant method. D = 10%, h = 20 ft D = 20%, h = 8 ft D = 5%, h = 10 ft L= 125 ft Fig. Q3(d)
NW NE 310 210 SW SE 1:10,000 4.5 cm If aquifer hydraulic conductivity and effective porosity are found to be 0.2 m/day and 0.25 respectively, how long (in years) will it take groundwater to travel from well 310 to well 210? 1 year = 365 days Answer: 200- -300
Situation 3:The water table in a certain deposit of soil is at a depth of 2m below the ground surface. The soil consists of clay up to depth of 4m from the ground and below which lies sand. The clay soil is saturated even above the water table:Clay strata: ? = 30%, ?? = 2.72Sandy Strata: ? = 26%, ?? = 2.64 1. Compute the total pressure.2. Compute the pore water pressure.3.Compute the effective stress pressure at a depth of 8m below the ground surface.
The water table is lowered from a depth of 10 ft to a depth of 20 ft in a deposit of silt. All the silt is saturated even after the water table is lowered. Its water content is 26%. Estimate the increase in the effective pressure at a depth of 34 ft on account of lowering the water table. Assume G, = 2.7. 34 ft 20 ft 10 ft 10 ft Silt deposit Figure Ex. 5.7 Original G.W.L. Final G.W.L.
The soil under a dam consists of five layers as follows: Hydraulic conductivity (cm/hr) Layer Depth (m) 1 5 4.8 2 2 8.0 3 0.6 18.0 4 1.0 3.0 5 3.5 1 Calculate: v What is the average vertical (perpendicular to flow) hydraulic conductivity of the soil? V What is the transmissivity of the soil, given the water table is at the ground surface?
Q 2.An aquifer has following different formations, their thickness and Hydraulic conductivity are given below. Assume that each formation is isotropic and homogeneous. Compute both the equivalent horizontal and vertical hydraulic conductivities Formation Thickness (m) Hydraulic Conductivity (m/day) 1 8.5 19.7 8 26.4 12.5 33.1 16 34.8 10.5 19.5 15 29.2 16.5 26.9 18 34.6 16.5 27.3 18 18 21.5 44.7 26 36.4 27.5 32.1 25 46.8 28.5 55.5 34 52.2 30.5 38.9 36 51.6 33.5 33.3 32 40 41.5 41.7 43 56.4 37.5 46.1 40 61.8 43.5 48.5 45 73.2 41.5 46.9 50 56.6 44.5 63.3 55 70 52.5 62.7 56 70.4 53.5 83.1 53 70.8 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34