ww R1 V 2 sine sine In the above circuit, let R1 = 8 ohm, reactance of L1 be j12 ohm. RMS value of the voltage source is 180 volt at phase angle 0 degree. The voltage source supplied 2.5 KW and 0.4 kVaR power. Determine the current source value in complex phasor form. Re(1) = ampere Im() = ampere ell t L1

ww R1 V 2 sine sine In the above circuit, let R1 = 8 ohm, reactance of L1 be j12 ohm. RMS value of the voltage source is 180 volt at phase angle 0 degree. The voltage source supplied 2.5 KW and 0.4 kVaR power. Determine the current source value in complex phasor form. Re(1) = ampere Im() = ampere ell t L1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

answer in 4 decimal places.
calculate phasor currents I1 and I2 in the circuit shown below
Determine the phase angle difference. Write the values only in degrees in four decimal places. the correct answer is 90 degrees. show the solution please. thank you
1. Solve for I rms. 0.785 and b = 3.37. a = i(wt) = 21.8 sin (wt – 1.312) – 50 + 75.0e¯®t/3.77 A for 0.785
A Time left 0:51 Z1 22 V sine sine B Let Z1 = 3+j4 ohm and Z2 = 3-j4 ohm. Let the current source phasor be I = j10 ampere and V = 50 volt and phase angle 0 degree. Both sources operate at 50 Hz. Real part of the Thevenin Voltage phasor between nodes A and B is Volt Imaginary part of the Thevenin Voltage phasor between nodes A and B is Volt Real part of the Thevenin Impedance between nodes A and B is Ohm
supply 3. Three circuits A, B and C are connected in series across 350 V supply. The voltage across circuit A is 80 V lagging the voltage by 330 and the voltage across circuit C is 140 V leading the supply voltage by 48°. Determine the voltage circuit B and its phase displacement from the supply voltage using wave and vector solution. across 4. Draw the phasor and wave diagram of the following sinusoidal current:
How about the average power on each elements? And is it absorbing or delivering power too?
If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b. -12000 + j16000 VA Oc. 12000 + j16000 VA O d. None of these
A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin400Ot) A is applied to the circuit shown. Find the total power? * İL www 1C iT -J9N J42 20 W 55 W 39 W 28 W
Solve it quickly please
2) Determine the open circuit voltage (Voc) and short circuit current (Isc) for the circuit shown below. Hence draw the Thevenin equivalent circuit and the maximum power which can be transferred to the load. (20V,2.5A, 12.5W) 3A 1202 24V 6Ω ww W 4Ω a b M RL
Find the apparent, reactive and active power in each element of the following circuit Circuit for power analysis