SINE(0 6Vp-p 1.5K) R₁ LL 2.5 mH 100 PL On the load, find the Power (P) in Watts (W) R A 180//180 Ω 5.4 mH 2.5 mH 100 SINE(0 6Vp-p 1.5K) B 220//220 Ω 2.7 mH Load

Q: The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? R V V3 23…

A:

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is applied to the circuit…

A:

Q: Given the Figure 3 as shown below, determine: R a) Draw the Phasor diagram in terms of: 250 2 1.…

A:

Q: calculate the magnitude of the current through the j3.3k ohm inductor. jl k2 1.2 k2 -j4.7 k2 j2.2 k2…

A:

Q: assume that the voltage drop across the resistor ER is 78 v the voltage drop across the capacitor EC…

A:

Q: The rms value of the resultant current in a wire which carries a dc current of 20 A and a sinusoidal…

A: Given information is shown below:D.C. current or average current Peak value of sinusoidal current To…

Q: 5. Let's change our square wave to be less square. We're only going to have it be at the high…

A:

Q: Determine the rms current I as shown in figure 1. Source voltage is eady in RMS value (Answer must…

A:

Q: Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and…

A: For the given data to limit 20Vrm

Q: In an inductive circuit, What is the value of the instantaneous current if t-40 s .L= 10mH and v(t)…

A: Find the Instantaneously current at time to= 40s Voltage and inductance are given.

Q: find average power of the voltage source 10Ω j10 2 -j5 -j2.4 2 j102

A: In this question , we will find average power from voltage source..

Q: Find the rms values for v = 120 V sin(3771 + 15°) and i = 8.5 x 10 A sin(2nt + 65°).

A: In this question we need to find a RMS value of voltage and current .

Q: The frequency of a sinusoidal alternating current is 65 Hz and its maximum value is 12 A. The…

A: sinusoidal alternating current Frequency f=65 Hz maximum value Im 12 A. The current starts at zero…

Q: Problem 3 Compute the average and rms voltage of the waveform shown in the figure below. 6 V 4 ms 4…

A: The given waveform is:

Q: i (A) 1 cycle 6 10 t (ms) -2 -10 4.

A: To find Average and RMS value of the waveform

Q: Tu netuork show in opeating in the thndy doulce. If V, = 2aes2t state wilh sinusoidal ve and V, 2…

A:

Q: An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is…

A: (a) Write the given values. Vrms=22.2 VL=0.29 mHf=1 kHz

Q: If the alternating current equation is i = 64.8 sin 423 t. What will be the average current?

A: Given:  Alternating current equation i = 64.8 sin 423 t We have to determine the average value of…

Q: A solenoid with an inductance of 0.25 H and a resistance of 100 is connected to a 120-V 60-Hz…

A:

Q: What is the value of Z, in the following figure? a 4/0° A (O j102

A: To calculate the value of Thevenin impedance Zth

Q: A non-sinusoidal voltage (e=20+15sin2000t+ 10sin6000t+5sin8000t) Volt is applied to the circuit…

A:

Q: Question 17 If I average a positive half-cycle sinusoidal current, what value will I get? O zero O…

A: The solution is given below

Q: The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 3.5V what is V3? R L VI V2

A:

Q: The equation for an alternating current i of frequency 50 Hz and RMS value 70.7 A is given by i=…

A: Given, Frequency, f = 50 Hz. RMS value of current, Irms=70.7 A. Peak value of current, Im=2irms=100…

Q: What is the value of the equivalent admittance? 100 ww sa -20 j10 a

A:

Q: A triangular voltage source has a peak value of 10 V. What is the computed RMS value of this source?…

A:

Q: ... Vx rell ell 10 V sine j5 V sine -j10 Q @node x: Y11Vx = Isc1 RE IM RE IM Y11 Blank 1 Blank 2…

A:

Q: 5 Find the steady-state expression for v, in the circuit = = 200 cos 5000t mA. of Fig. P9.26 if i g…

A: Using current division rule, find the current through the 240 ohms resistor. By ohms law , voltage…

Q: For the Photoflash unit. Vse 9V R15KQ. C-1500 uf. R2 120. The average power dissipated by the lamp…

A: As per guidelines given to us, we can only provide the solution of one question in multiple type of…

Q: 2. Sketch Vout if Vin is a 30 V peak to peak sinusoidal wave, D1 is germanium and D2 is silicon.…

A:

Q: For the circuit below with a sinusoidal voltage source, determine the average power supplied be the…

A:

Q: The average value of a sinusoidal current is 300A. What is it’s rms value? Group of answer choices…

A:

Q: Q5] find the current of the resistance 1892 if the value of the source is 7.4sin(100πt-44) volt 1mF…

A: 5)  To find the current through 18 ohm resistor in the circuit

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.