Write your answer in 4 decimal places. DO NOT round off intermediate values. Water (Cp = 4180 J/kg-K) enters a 4-cm-diameter tube at 15°C at a rate of 0.06 kg/s. The tube is subjected to a uniform heat flux of 2500 W/m2 on the surfaces. The length of the tube required in order to heat the water to 45°C is m

Write your answer in 4 decimal places. DO NOT round off intermediate values. Water (Cp = 4180 J/kg-K) enters a 4-cm-diameter tube at 15°C at a rate of 0.06 kg/s. The tube is subjected to a uniform heat flux of 2500 W/m2 on the surfaces. The length of the tube required in order to heat the water to 45°C is m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.17P: Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID,...

See similar textbooks

Similar questions

Write your answer in 4 decimal places. DO NOT round off intermediate values. Hot water flows through a PVC (k = 0.092 W/m-K) pipe whose inner diameter D is 2 cm and outer diameter is 2.5 cm and outer diameter is 2.5 cm. The temperature of the interior surface of this pipe is 35°C and the entire exterior surface at 20°C. Determine the rate of heat transfer per unit of pipe length
Heat Transfer (Third year) 2020- 2021 Homework 01-03-2021 By Dr. Basil Noori Merzah one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at T01-320°C flows in a cast iron pipe (k=80W/m. C) whose inner and outer diameters are D,=5cm, and D,-5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m. C. Heat is lost to the surroundings at T2-5°C by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m."C. Taking the heat transfer coefficient inside the pipe to be 2 0 h,-60W/m. C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. Q5/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D =3.34 cm steel pipe (k=54.0W/m. C) for the following conditions: inside and outside heat transfer coefficients are…
Air enters a 7-cm-diameter and 5-m-long tube at 65°C and leaves at 15°C. The tube is observed to be nearly isothermal at 5°C. If the average convection heat transfer coefficient is 20 W/m2.°C, determine the rate of heat transfer from the air. (Solve using EES, and round the answer to 2 decimal places.) The rate of heat transfer from the air is 491 W.
Q1: Consider a wall heated by convection on one side and cooled by convection on the other side. Show that the heat-transfer rate through the wall is T1-T2 1/h A+A/kA+ 1/h2A Where T; and T; are the fluid temperatures on each side of the wall and h, and h; are the corresponding heat-transfer coefficients.
i need the answer quickly
Q1 a) What is the physical significance of Reynolds number? Write down 5 (five) factors that influence the convection heat transfer rates. b) Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 7-m- long tube. The tube is equipped with an electric resistance heater, which provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat from the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 8 L/min, determine the convection heat transfer coefficient and temperature at the inner surface of the pipe at the exit. Q2 a) Consider heat transfer to oil flow inside a copper pipe. Is the pipe length affecting the heat transfer rate into the oil? Briefly explain. b) Used engine oil can be recycled by a patented reprocessing system. Suppose that such a system includes a process during which engine oil flows through a…
Write your answer in 4 decimal places. DO NOT round off intermediate values. Use T(K) = T(°C) + 273. A 1-m-inner diameter liquid oxygen storage tank at a hospital keeps the liquid oxygen at 90 K. This tank consists of a 0.5-cm-thick aluminum (k = 170 W/m· K) shell whose exterior is covered with a 10-cm thick layer of insulation (k = 0.02 W/m K). The insulation is exposed to the ambient air at 20 °C and the heat transfer coefficient on the exterior side of the insulation is 5 W/m2. K. The temperature of the exterior surface of the insulation is °C
Kindly give me right solutions with clear calculations.
PLEASE ANSWER COMPLETELY AND CLEAN FOR AN UPVOTE!!!
The boiling temperature of nitrogen at atmospheric pressure at sea level (1 atm pressure) is -196 °C. Therefore, nitrogen is commonly used in low-temperature scientific studies since the temperature of liquid nitrogen in a tank open to the atmosphere will remain constant at -196 °C until it is depleted. Any heat transfer to the tank will result in the evaporation of some liquid nitrogen, which has a heat of vaporization of 198 kJ/kg and a density of 810 kg/m3 at 1 atm. Consider a 3-m-diameter spherical tank that is initially filled with liquid nitrogen at 1 atm and -196 °C. The tank is exposed to ambient air at 15° C, with a combined convection and radiation heat transfer coefficient of 35 W/m2⋅K. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the nitrogen inside. Determine the rate of evaporation (in kg/s) of the liquid nitrogen in the tank as a result of the heat transfer from the ambient air if the tank is insulated with…
Solve it pls.
The boiling temperature of oxygen at atmospheric pressure at sea level (1 atm) is -183ºC. Therefore, oxygen is used in low temperature scientific studies since the temperature of liquid oxygen in a tank open to the atmosphere remains constant at -183ºC until the liquid oxygen in the tank is depleted. Any heat transfer to the tank results in the evaporation of some liquid oxygen, which has a heat of vaporization of 213 kJ/kg and a density of 1140 kg/m3at 1 atm. Consider a 4 m diameter spherical tank initially filled with liquid oxygen at 1 atm and -183ºC. The tank is exosed to 20ºC ambient ait with a heat transfer coefficient of 25 W/m2. ºC. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the oxygen inside. Disregarding any radiation heat exchange, determine the rate of evaporation of the liquid oxygen in the tank as a result of the heat transfer from the ambient air