Write an assembly program that would control the pins of ATMega328P as the following: if (R20 > 0): Pin 27 turn on (HIGH) Pin 28 turn off (LOW) else if (R20 < 0): Pin 28 turn on (HIGH) Pin 27 turn off (LOW) else: Pin 27 turn off (LOW) Pin 28 turn off (LOW)

Write an assembly program that would control the pins of ATMega328P as the following: if (R20 > 0): Pin 27 turn on (HIGH) Pin 28 turn off (LOW) else if (R20 < 0): Pin 28 turn on (HIGH) Pin 27 turn off (LOW) else: Pin 27 turn off (LOW) Pin 28 turn off (LOW)

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 4VE

See similar textbooks

Similar questions

The ATmega32 is used to flash two separate LEDS. as follows: LED D1 will flash on a frequency 20 kHz and duty cycle of 70%. LED D2 will flash on a frequency of 10 kHz and duty cycle of 35%. Develop a C-code to program this ATmega. 22 23 24 25 26 27 28 29 RESET PCO/SCL PC1/SDA PC2/TCK D2 13 12 XTAL1 XTAL2 PC3/TMS PC4/TDO PC5/TDI 40 39 38 37 36 35 34 33 LED PAO/ADCO PA1/ADC1 PA2/ADC2 PA3/ADC3 PAAIADC4 D1 PC6/TOSC1 PC7/TOSC2 14 15 16 17 18 19 20 21 PDO/RXD LED PAS/ADC5 PAGIADC6 PATIADC7 PD1/TXD PD2/INTO PD3/INT1 PD4/OC1B PD5/OC1A PD6ICP1 PD7/OC2 PBOTOXCK PB1/T1 PB2/AINOINT2 4. PB3/AIN1/OCO PB4/SS PB5/MOSI 7. PB6/MISO AREF AVCC 32 30 PB7/SCK ATMEGA32
3.
1.1 Design a circuit for the traffic light unit in Multisim. The design should include 3 positive edge triggered D flip-flops. Set your clock signal to 1Hz. Please include Four screenshots of your working circuit, with each screenshot showing each of the light configurations shown in Figure 1. 000 100 010 110 001 Figure 1. A state diagram for a traffic light control The design should include 3 positive edge triggered D flip-flops. Use 1 flip-flop to control the on and off of a given light, and the state machine should switch from Red (100) -> Red and Amber (110) - > Green (001) -> Amber (010) and repeat the cycle again, with the following transition table: Current state Next state 000 100 100 110 110 001 001 010 010 100 ABC A*B*C* Table 1. A transition table for the traffic light unit
It is desired to configure a PWM Output Pin on an ATmega328P. Write the AVR Assembly code that will set up an output pin for one of the 8-bit timers (Timero or Timer2) to meet the following specification: Phase Correct PWM, TOP = $FF, Output is NON-INVERTED, PWM frequency is 980 Hz and the duty cycle is 33%.
If it's too hard, answer partially
Here's a table showing the tco and tro for each of the components in the circuit bellow. Please compute tco and tpo for the whole circuit? tco tPD B Inverter 0.1 ns 0.6 ns AND2 0.4 ns 0.8 ns C XOR2 0.5 ns 1.8 ns MUX2 0.5 ns 1.5 ns
The connection diagram shows multiple gates and the pins assigned to each gate. For example, from the datasheet connection diagram of IC 7400, four individual NAND gates can be observed. Pins 1, 2 and 3 are all related to one of the four NAND gates. For each gate the top input is assigned the letter A while the bottom input is assigned B and the output is assigned the letter Y. The function tables of the ICs are normally given in terms of H (High logic level) and L (Low logic level). Referring to the datasheet function table of IC 7400 shows the four different input combinations of A and B and the corresponding output Y for one of the four NAND gates. There is also one more letter assignment that could be found in function tables, this is the letter X, a don't care assignment. In cases where an X is given, it can be replaced by either an H or L assignment without effecting the resultant functionality of the IC. An example of this case can be seen for the function table of IC 7402. The…
Complete the timing diagram for the following circuit. Assume that the signal delay through the NOR gates is 3 ns, and the delay through the NOT gate is 1 ns.
(Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)* Decoder 74hc138Or you can use 74HCxx versions.) Task 3: Design a Binary Ripple Carry Adder for 5+3 summation in BCDcoding system. Draw the the circuit diagram by using FullAdder Blocks. Simulate the circuit.
Q2: A- Here's a table showing the teo and tro for each of the components in the circuit bellow. Please compute teo and tro for the whole circuit? B- Redesign the logic circuit using universal logic gates: NAND and NOT? Inverter 0.1 ns 0.5 ns :) AND 0.4 ns 08 ns XOR 0.5 ns 13 ns OR 0.4 ns 09 ns NAND 0.3ns 0.7 ns
Write a Test Bench for the Five-Cycles High Laser Timer (please see the VHDL code for reference).
Given in the figure is IC 7474 pin configuration. The pin connections of the IC is provided in the Table for the design of a particular counting sequence. What is that counting sequence for which it is desined. Intially the FFs states (AB) were reset to 00. 74LS74 Dual D-type Flip Flop D-type Flip-flop Two vcc CLR D CLK PR 14 13 U 12 1110 PR CLK CLR HCLK 아 CLR D CLK PR GND D-type Flip-flop One Table Signal Value VcC (Logic 1) PIN NUMBERS 1, 4, 10, 13 and 14 3 and 11 Connected with a common clock A A' 7 Ground (Logic 0) 8 B' 9 B Is connected with PIN 8 Is connected with PIN 5 2 12 21 O a. (AB): 00 --> 01 -->10 --> 11 --> 00 O b. (AB): 00 --> 10 --> 01 --> 11 --> 00 O c. (AB): 00 -->10 --> 11 --> 01 --> 00 O d. (AB): 00 --> 10 -->11 --> O1 --> 00