Write an 8086 program to store the remainder of the division (Y=X/Z) to thememory location which has an offset address of 1414H. (Note: use X=73H andZ=0CH)(2.5 marks)

The 8086 program calculates the remainder of the division Y=X÷ZY = X \div Z, where X=73HX = 73H and…

Answered: Write an 8086 program to store the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

New Solution
To select the ROM the address lines A10-A9 should be: A. 00 B. 01 C. 10 D.10
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
Assume a block diagram for a clock divider that can take a 1 MHz oscillator and create a signal that has clock frequency of 20 Hz. What is the terminal count value needed to create this frequency and the number of bits needed on the counter if the clock divider can select between a 20 Hz signal and 2 kHz signal?
24. a. The serial adder required six clock pulses to add two, three bit binary numbers. (True or False. Write the correct one, if it's false) b. A three bit parallel adder circuit uses three adders to add all bits on two clock pulse. (True or False. write the correct one, if it's false) c. What is the two's complement of 1001?
Q3/(A) False OR True 1- A0-0 and BHE-1 are used as low bank-select signal: 2-AX is 2234 H after executing the following instruction: AAS. If AX-2234H. 3-IP register holds the offset address of the next instruction to be executed. 4- The XLAT instruction in 8086 assembly language is used to perform arithmetic operations between two memory operands. 5- Bus interface unit is responsible form
Draw a 2x1 multiplexer block diagram.Create the status table. Find the simplest form of circuit output with Karnaugh.Explain the circuit problem that may occur.What should be done to fix the problem?(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
5. The following diagram represents a four-bit ring counter. Assuming a starting state of Q3 = 1 and Q₂ = Q₁ = Qo= 0, complete the timing diagram. Explain how this counter works. CLK 23 2₂ 2₁ 20 D CLK Q3 D 22 >CLK D 2₁ >CLK D CLK Lot
QO dddd Q1 clock Given: • Counter starts at decimal 9 when Q viewed as a 4-bit unsigned number (Q3 most significant bit) What is the decimal value of Q (viewed as a 4-bit unsigned number) after four more clock “ticks"? Answer
Question : with Eight LEDs with 74HC595. This code uses a shift register to use a single data pin to light up 8 LEDs. The code uses the command "bitSet" to set the light pattern. What is the value of the variable leds when the value of currentLED is 5? Hint: You can use Serial.begin(9600) in the setup and Serial.println(leds) in the loop to examine this value. Answer must be a numerical value
1. Convert: 0.FF16 = _____________ 10 2. Convert from Binary to Gray code: 11010100102 = _______________________ Gray code 3. BCD Addition: 7892 + 797 = 4. Signed Binary Operation: -85310 - 39810 I need answer ASAP. Thank you so muccch!!
(a) Consider the flipflop circuits below: (i) Name the 2 circuits given in the figure. Explain how they are different from each other. a. b. (ii) Choose from the list the input that triggers data to travel to the next flipflop in a counter. A: Input at top NAND gate B: Input at bottom NAND gate C: Clock input clk Q

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Write an 8086 program to store the remainder of the division (Y=X/Z) to the memory location which has an offset address of 1414H. (Note: use X=73H and Z=0CH) (2.5 marks)