Wn = 2 k/ft = ? k/ft AW 33 x 130 section of A992 steel is used as a simply supported beam as shown. If lateral support is provided at both supports and at every 8 ft and the applied service dead load is 2 k/ft, determine the 8 ft 8 ft 8 ft 32'ft maximum service live load that can be put on this beam n = 2 k/ft (including beam weight)

Wn = 2 k/ft = ? k/ft AW 33 x 130 section of A992 steel is used as a simply supported beam as shown. If lateral support is provided at both supports and at every 8 ft and the applied service dead load is 2 k/ft, determine the 8 ft 8 ft 8 ft 32'ft maximum service live load that can be put on this beam n = 2 k/ft (including beam weight)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A beam has the following distributed loads : wD = 0.44 kip/ft, and wL 0.76 kips. If the beam is W 18 x 50, braced at the ends and third points, made from A992 steel, by directly applying the provisions of the AISC Specification, what is the available flexural strength of this beam? What is the adequacy of this beam in providing the required flexural strength. L 35'
please solve question 4.2, quickly please
A W36x210 can be used for Transfer Girder ‘A’ as shown in the elevation next page.Assume the LRFD loads on the ‘Transfer Girder’ are as follows:Pu= 200 kips from the column above. Assume also that the loads from self-weight of thewu = 2.0 kip/ft (girder self weight and beams framing into this transfer girder are equivalentto a uniformly distributed load). These loads are shown in the last figure.a) Check whether the W36x210 ‘Transfer Girder’ is adequate for bending and shear.Assume the unbraced length Lb =20 ft.b) Suppose that service loads, w and P, are both 50% dead load and 50% live load. Does theW36x210 satisfy a service live load deflection limit of L/480?
Homework 1- For a simply supported beam with span 6.0 m , determine the area of steel required to reinforced the beam(350*550) mm if it subjected to service dead load (including to self-weight) (40 kN/m) and service concentrated live load (PL 100 kN) use f'c = 25 MPa & fy 350MPA P= 100 kN Wdl= 40 kN/m 550 mm 350 mm
The compression member shown is made of HE300B section. If Fy is equal to 320 MPa:a) Check the section for local buckling. b) Determine the maximum compressive service load that can be supported if the live load is twice as large as the dead load.
RCDA reinforced concrete T- beam, section in Figure 2 (a), is subjected to an ultimate uniformload and concentrated loads as shown in the Figure 2(b). The beam is reinforced with 6-28 mm diameter tension bars at the point of maximum positive moment (at midspan -bars at the bottom), and 3-28 mm diameter tension bars at the point of maximum negativemoment (at the supports - bars at the top) .. The design properties used are: f ‘c = 21MPa and fy = 414 MPa, ; flange width = 650 mm, flange thickness is = 90 mm; webthickness = 250 mm; effective depth = 410 mm.Need to answerQ. Draw the shear and moment diagrams for the given loads;
In the built-up girder shown below that has an unbraced length of 25 ft. (L-25 ft) and moment gradient factor of C,-1, determine the maximum flexural design strength. E-29000 ksi Fy-50 ksi PL 25x0.6" PL 35*0.3" PL 25x0.6"
Problem 4: Determine LRFD flexural capacity (OMn) for a W21x73 used as a beam with an unbraced length of the compression flange of a) 6 ft, and b) 12 ft. Use A992 steel (F, = 50 ksi) and Ch 1.0.
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
need asap auto like
The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?
Problem 2 and 3 are related