Answered: With the help of a labelled schematic…

Engineering

Mechanical Engineering

With the help of a labelled schematic diagram show the path of a warp yarn in a High Speed modern Warping Machine.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter23: Fabricating Techniques And Practices

Section: Chapter Questions

Problem 2R: What is a cost advantage of using preformed parts in a fabrication?

See similar textbooks

Similar questions

Briefly explain the Spinning process (primary shaping process) ? ( Type the report in word format) (Type by kepord )(minimum 1 page write up)
Please explain some methods for printing suitability and materials used for 3D printed applications in Aerospace, as Printed Winglet or wing module.
Based on the table below, which of the statements below is/are correct regarding the 3D printing process shown in the schematic? a.You can produce a room-temperature non-fragile 225C oven-safe food container with at least one material from the above table using this process and a 280C nozzle b.You can use this process to print plastic or brittle objects but not elastomers and rubbers c.Manufacturing a thermoplastic HDPE hose with an extrusion nozzle heated to 175C is possible with this process d.You can print thermoplastic and thermoset polymers with this process, you only need to make sure that the nozzle specs and the crosslinking conditions match the polymer requirements e.This process is best suited for the low volume production of tubes, bars and beams due to the nature of the extrusion process
Describe the principles and applications of 9D printing and its theoretical potential for advanced material design.
What is the significance of print spooling in the printing process, and how does it work?
3. A dimension of 225.00 mm is specified for a particular injection moulded component manufactured in ABS. Calculate the corresponding dimension to which the mould cavity should be machined, using the value of shrinkage given in the table below. Typical values of shrinkage for moldings of selected thermoplastics. Shrinkage, mm/mm (in/in) Shrinkage, Plastic Plastic mm/mm (in/in) ABS Polyethylene Polystyrene 0.006 0.025 Nylon-6,6 Polycarbonate 0.020 0.004 0.007 PVC 0.005
Based on the table below, which of the statements below is/are correct regarding the 3D printing process shown in the schematic? Z AXIS X AXIS YAXIS LEGEND A: Extruder B: Nozzle C: Printed part D: Hot plate E: Filament Table 15.2 Melting and Glass Transition Temperatures for Some of the More Common Polymeric Materials Material Polyethylene (low density) Polytetrafluoroethylene Polyethylene (high density) Polypropylene Nylon 6,6 Polyester (PET) Poly(vinyl chloride) Polystyrene Polycarbonate Glass Transition Temperature [°C (°F)] -110 (-165) -97 (-140) -90 (-130) -18 (0) 57 (135) 69 (155) 87 (190) 100 (212) 150 (300) Melting Temperature [°C (°F)] 115 (240) 327 (620) 137 (279) 175 (347) 265 (510) 265 (510) 212 (415) 240 (465) 265 (510) a. This process is best suited for the low volume production of tubes, bars and beams due to the nature of the extrusion process b. Manufacturing a thermoplastic HDPE hose with an extrusion nozzle heated to 175C is possible with this process □c. You can…
Drawing on the discussion of the production of polyester textiles. Give a detailed and compelling flowchart of the process, beginning with the raw materials and ending with the finished product, and describe each step of the process individually. It would be helpful if you included illustrations, figures, and animations.
Describe the principles of 7D printing and its theoretical applications in materials science and advanced manufacturing.
In a single-barrel extrusion system, the operator observes that the extrudate (made of polyethylene, PE) is being processed at a speed of 0.5m/s with a final diameter of 0.5cm. The screw pitch is 1cm, the barrel diameter is 1.5cm, the barrel length is 10cm, the screw channel depth is 0.3cm and the screw is rotating at 10RPM. a. Find the head pressure on the die given that the polymer has a viscosity of 300Pa.s. Note that the swell ratio of PE is 1.2. b. Find the length of the die opening.
In a single-barrel extrusion system, the operator observes that the extrudate (made of polyethylene, PE) is being processed at a speed of 0.5m/s with a final diameter of 0.5cm. The screw pitch is 1cm, the barrel diameter is 1.5cm, the barrel length is 10cm, the screw channel depth is 0.3cm and the screw is rotating at 10RPM. a. Find the head pressure on the die given that the polymer has a viscosity of 300Pa.s. Note that the swell ratio of PE is 1.2. b. Find the length of the die opening.
How is paper made?