A stick of butter at 35°F measures 1.25 in. x 1.25 in. x 4.65 in. and weighs 4.2 ounces. Find its specific weight. y =

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: As asked only the first three are solved. φ(x,y)=sinxAx2e-y+Bey

Q: A closed piston-cylinder system consists of 3.0 moles of monatomic gas, initially at temperature…

A:

Q: y

A:

Q: *2-4. The vertical force F acts downward at A on the two- membered frame. Determine the magnitudes…

A:

Q: -114. Determine the magnitude of the projection of F₁ along the line of action of F2. 2-115.…

A: Given data  F1= 30(lb) and F2=25(lb) Find the magnitude of the projection of F1 along the line of…

Q: Q17-In problem Q16 determine the percent elongation. (b) If the specimen necked to an area = 92mm2,…

A:

Q: Determine the force in members BC, FC, and FE and state if the members are in tension or…

A: from the FBD,

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 2 D2=20 cm P2=? Kpa…

A: Continuity equation is based on the conservation of mass. If a pipe having area at one section is…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: *2-72. Two forces F₁ and F2 act on the screw eye. If the resultant force FR has a magnitude of 150…

A: Two forces F1 and F2 act on the screw eye.If the resultant force FR has a magnitude of 150 lb and…

Q: 1 Legs of a pneumatic system are generally equipped with and work stations receive air which meets…

A: This question is based on the concept of legs of pneumatic system and SUS.

Q: 5) 1000 kg of potatoes are processed to obtain french fries. Raw potatoes are washed, peeled, cut…

A: Given: (a) The french fries are made from potatoes which can be shown by following flow chart.

Q: Wall thickness of a pipe is identified by A) Normal rating B) Schedule number C) Dash number D)…

A: This question is based on the concept of wall thickness of pipe and pneumatic directional valve.

Q: te the force in each member of mber is in tension or compression.

A:

Q: 1-23.Determine the length of side C of the triangle shown in Figure P1-23.

A:

Q: Consider a Carnot vapor refrigeration cycle with Refrigerant 134a as the working fluid. The cycle…

A: Given:Cold region temperature, TC=40oFThe ambinet temperature, TH=90oFFind:Coefficient of…

Q: Explain the Beam radiation and diffusive radiation with necessary diagram.

A: Solution (1): The beam radiation and the diffuse radiation are the components of solar radiation.…

Q: 3. In the figure below two equal forces are applied to the tap wrench a distance d from the center…

A:

Q: Answer D

A:

Q: Instructions: Identify the talking components by choosing the most appropriate answer from the…

A: To determine: I directly determine what the speed of a hydraulic actuator is going to be. What am…

Q: The emissivity of iron is approximately 0.25. If an iron cube (with a side length of 0.5 m) is…

A: This question is related to heat transfer. heat transfer is due to temperature differences. the mode…

Q: 7. The relative humidity on a 90°F day is 30 per cent. a. How many pounds of water vapor are in a…

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: Your professor at HTU asked you to explain Archimedes topic to your classmates at one of the classes…

A:

Q: 9. An R-L series circuit contains a resistor and an inductor. The resistor has a value of 6.5 2. The…

A: Question - 10: The voltage drop across the resistor in an R-L series circuit can be found using…

Q: 2.5". 45 45°

A: Let’s divide the shaded area into two sections. Section 1 is a circular arc OCD and section 2 is a…

Q: a Determine the Force gg AC 6 Determine the Forde AB 2' + 8' 350

A: Given: To find: Force AB , AC

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

A:

Q: m = 0.350 kg. (c) Is the original energy in the spring or in the cord? (d) Explain your answer to…

A: For the option e and f and g  The solution is ttached in step 2 below

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: 2) What is the magnitude of R and Cr in pt B?

A: Solution: Given Data: The force and moment system is shown below:   To Find:

Q: 11. Determine the magnitude of the force P acting from A toward D to cause a moment of 200 lb-ft…

A: Dear student please rate me postive :) Stay safe stay happy !   Data given - Moment = 2000 lb - ft…

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: Here, we have to complete the relationship among fluid conductors and connectors by choosing…

Q: 3. Determine the magnitude of F, and its direction 0 so that the resultant force is directed…

A:

Q: slove f

A:

Q: Consider an ideal gas with constant cp =R and in an initial state at 300K and 100 kPa. (a) Compute…

A:

Q: Please solve d through g

A: a)Original dimension: 400mm*100mm*25mmFinal dimension: 400mm*125mm*20mmb)Effective strain=…