QUESTION 5While driving down a highway early in the evening, the air flow over an automobile establishes an overall heat transfer coefficient of 30 W/m?K. The passenger cabin of this automobile exposes 8 m2of surface to the moving ambient air. On a day when the ambient temperature is 35°C, how much cooling must the air conditioning system supply to maintain a temperature of 22°C in the passengercabin?O a. 670 wO b. 1284 WOC. 2106 WO d. 2565 WO e. 3120 WO f. None of them

Given data, Heat transfer coefficient h = 30W/m2 K T∞ = 35°CTin = 22°CA = 8 m2

While driving down a highway early in the evening, the air flow over an automobile establishes an overall heat transfer coefficient of 30 W/m2K. The passenger cabin of this automobile exposes 8 m of surface to the moving ambient air. On a day when the ambient temperature is 35°C, how much cooling must the air conditioning system supply to maintain a temperature of 22°C in the passenge cabin? O a. 670 W O b. 1284 W OC. 2106 W O d. 2565 W O e. 3120 W O f. None of them

While driving down a highway early in the evening, the air flow over an automobile establishes an overall heat transfer coefficient of 30 W/m2K. The passenger cabin of this automobile exposes 8 m of surface to the moving ambient air. On a day when the ambient temperature is 35°C, how much cooling must the air conditioning system supply to maintain a temperature of 22°C in the passenge cabin? O a. 670 W O b. 1284 W OC. 2106 W O d. 2565 W O e. 3120 W O f. None of them

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

700 W/m3 electrical heat is generated in a large plane wall whose one side is insulated while the other side is subjected to convection. The thermal conductivity of the wall is (k W/m.K) and the convection heat transfer coefficient is (h = 17 W/m?K). Determine the location and the value for the maximum temperature and the minimum temperature in the plate for steady one-dimensional heat transfer. Assume T. = 25°C. A=1 m?; L= 25 cm). = 20
In the system given in the figure below, a glass is heated under winter conditions. Since there are convection conditions on both surfaces of this glass, how much should the heat flow of the film heater be, considering that the t∞2 temperature is between 0-30?
Question 1 An electric current of 6.4 A passing through a resistor has a measured voltage of 9V across the resistor. The resistor is cylindrical with a diameter of 2.5 cm and length of 15 cm. The resistor has a uniform temperature of 115°C and the room air temperature is 23°C. Assuming that heat transfer by radiation is negligible, determine the heat transfer coefficient by convection.
It is desired to analyze heat transfer (or thermal load) and miscellaneous loadsfor a light work activity where there are 3 people in aresidential room located in the State of Durango, Santiago Papasquiaro, fordetermine the energy efficiency of the heating system in the heating seasonwinter, consider the interior temperature of the room to be 22 °C, and the coefficients ofindoor and outdoor heat transfer as 10 and 25 W/m2. °C respectively. Theroom has the following characteristics and electrical devices:
explain how heat transfer can be applied in terms of agriculture and machinery?
Question 2:A circuit board houses on its surface120 closely spaced logic chips, each dissipating 0.12 W. If theheat transfer from the back surface of the board is negligible, calculate (a) the amount of heat this circuit board (15 cm x20 cm) dissipatesduring a 10-hour period, in kWh, and (b) the heat flux on thesurface of the circuit board, in W/m2
In the walls of a warehouse, the inner plaster thickness is 2 cm and the heat conduction coefficient is 0.60 W / moC, the curtain concrete thickness is 10 cm, the heat conduction coefficient is 1.3 W / moC, the outer plaster is 2.5 cm and the heat conduction coefficient is 1.2 W. It is known to be / moC. Inner surface heat transfer coefficient is 8 W / m2oC and outer surface heat transfer coefficient is 21 W / m2oC. Indoor temperature, outdoor temperature and relative humidity of indoor environment are given in the table. How much of the insulation material with thermal conductivity coefficient should be used between the gas concrete and the outer plaster in order to prevent condensation on the inner wall of this warehouse. The indoor and outdoor ambient temperatures of the warehouse and the relative humidity of the storage environment are given in the table.K insulation: 0.032T inner: 14T outside: -15Relative humidity: 60
Express final answers in foursignificant figures.
The thermal conductivities of human tissues vary greatly. “Fat” and “skin” have conductivities of approximately 0.200 W /m 0K and 0.0200 W /m 0K, respectively, while other “tissues” inside the body have conductivities of approximately 0.500 W /m 0 Assume that between the core region of the body and the skin surface lies a “skin” layer of 1.00mm, a “fat” layer of 0.500 cm., and 3.20 cm. layer of other “tissues”. A)Find the R-factor for each of these three layers, and the R-factor for all layers taken together
9- Consider a flat plate solar collector placed at the roof of a house. The temperatures at the inner and outer surfaces of glass cover are measured to be 28°C and 25°C, respectively. The glass cover has a surface area of 2.2 m and a thickness of 0.6 cm and a thermal conductivity of 0.7 W/m C. Heat is lost from the outer surface of the cover by convection and radiation with a convection heat transfer coefficient of 10 /m2 °C and an ambient temperature of 15°C. Determine the fraction of heat lost from the glass cover by radiation.
Good Day, Please solve this question. Thank you
Q2 FigureQ2showsaHeatingRoom,whichpartlyisolated.Thereisathermalsystemconsisting of an electric heater in a room. Heat input by the heater is Q1and heat loss from room is Q2. Air in the room is at uniform temperature, ?, and surrounding temperature is ?o. Thermal capacity of the room is C, and wall thermal resistance is R. (a) Determine a mathematical model of temperature of the room. (b) DeterminetheTransferFunctionoftheheatingroom. (c) Determine the output response of the system when a step input 25°? is given.