Which sensor, when it comes to sensitivity, willbe favoured as a biosensor, the one with greatsensitivity or the one with low sensitivity? Justifyyour position using examples.

Biosensors can be defined as the devices that are used for the determination of the concentration of…

Answered: Which sensor, when it comes to…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

W Q.2) A Full-wave bridge rectifier with a (400 Sin(100)t) sinusoidal input has a load resistor of (10KS) .Sketch Vo and determine the : 1- Fi and Fo So 2- Vdc 2%. 〃 3- Vrms 4- Irms 5- Prms 6- Pdc PHO 7- Efficiency 8- Ripple Factor 9- PIV (.
A peizoelectric type sensor of sensitivity 300 Hz to 300 kHz. For a constant (dc) pressure of 100 kPa, the steady state output of the sensor in mllivolt is
A control system is to provide a regulation of flow in range of 20gal/min to 100gal/min. A linear flow sensor has a sensitivity of 0.1??/(gal/min) with 4mA at 20gal/min. The sensor has an uncertainty of ±6%. a) What is the sensor current at 40gal/min? b) What is the range of the output current at 40gal/min? c) A current-voltage signal conditioning circuit with sensitivity of 0.4V/mA ± 5%; what is the output voltage range at 40gal/min?
CONSIDERING THE RECTIFIER WITH CAPACITIVE FILTER BELOW AND V1 = 120V, 60 HZ WITH RELATION TRANSFORMER OF 6:1 AND RL = 1K OHMS AND ALSO CONSIDER THAT THE DIODE HAS A DROP VOLTAGE OF 0.7 V AND A RIPPLE VOLTAGE OF 10% OF THE OUTPUT PEAK VOLTAGE, CALCULATE: A) THE AVERAGE VOLTAGE AT THE OUTPUT; B) THE CONDUCTION INTERVAL OF THE DIODES; B) THE AVERAGE CURRENT AT THE DIODE; C) THE PEAK CURRENT AT THE DIODE. 6:1 TR D1 120V 60 HZ V2₁ 2 V2₂ 2 D2 OBS.: NO NEED TO CALCULATE THE CAPACITANCE 1K VS RL
Q1/Define zero-crossing detector and, what is difference between inverting and non-inverting zero-crossing detector?
2. Suppose first that we want to measure the temperature of a room with the following components. Direct connection Vcc = 3.3 V LM35 ADC The sensor is the LM35 chip, which gives a voltage proportional to temperature in degrees of Celsius so that 0°C gives zero voltage. The scaling factor is 10 mV/°C, indicating that the LM35 gives 200mV at 20°C and so on. The sensor is a silicon IC, not a thermistor. Its output is a linear function of temperature, which is convenient, but the voltage is small. a) Suppose the ADC is a 10-bit SAR, common in small microcontrollers, which takes its reference from the supply at 3.3V. We wish to resolve changes of 0.1°C or better over a range of 5°C to 30°C. Suppose first that we connect the output of the LM35 directly to the input of the ADC. What voltages must we measure? Is it possible to meet this specification without further components? Why? b) If the specifications in a) cannot be met. You can use an external ADC with a better resolution. Assume that…
Describe at least two methods of checking the operation of hall effect sensors in car.(Automotive industry)
Discuss the importance of analog-to-digital converters (ADCs) in microcontroller applications. Provide examples of analog sensors commonly interfaced with microcontrollers.
Q1.A) If an 8-bit SAR ADC is used to digitize 8V full scale signal, what will be the digital o/p for an analog i/p of 5.76 V (perform complete analysis)?
Please solve step by step in handwriting notes on plane white paper. If any data is missing then you can assume data as you wish
Sketch the relationship between temp. and voltage of ECT & IAT sensors. 2:01 /
Explain the workflow of computational modelling process in 3D printed electronics.

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Which sensor, when it comes to sensitivity, will be favoured as a biosensor, the one with great sensitivity or the one with low sensitivity? Justify your position using examples.