Which one of given below is not a chip type? 31 - Aşağıdakilerden hangisi talaş türü değildir? Continuous chip with built-up edge A) yığma kenarlı sürekli talaş Discontinuous chip B) süreksiz talaş Multiple cutting edge chip çoklu kesme kenarı talaşı Serrated chip D) tırtıklı talaş Continuous chip E)

Which one of given below is not a chip type? 31 - Aşağıdakilerden hangisi talaş türü değildir? Continuous chip with built-up edge A) yığma kenarlı sürekli talaş Discontinuous chip B) süreksiz talaş Multiple cutting edge chip çoklu kesme kenarı talaşı Serrated chip D) tırtıklı talaş Continuous chip E)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. According to the figures as follows, please point out: 1) Gear hobbing cutter is 2) Milling cutter is 3) Wide edge cutter is ; 4) Grinding wheel is 5) Single point to cylindrical surface is b)
7-Which of the following lathe operations requires that the cutting edge of a tool bit be placed exactly on the work center line... а) Boring. b) Drilling. c) Facing. d) Turning. 8-In lathe, the carriage and tail stock are guided on... a) Same guideways. b) Different guideways. c) Any of the above. d) Not guided on guideways 9-. Slab milling can be performed more effectively by milling machine. a) Horizontal. b) Vertical. c) Can't say anything. d) None of the mentioned. 10-Cutting T-slots can be performed more effectively by milling machine. a) Horizontal. b) Vertical. c) Can't say anything. d) None of the mentioned.
Which one of the given options is right? a)Poor tolerance and surface finish in a part produced by broaching process b)The cutting tool used in broaching process is called single point tool c)Gear hobbing process is operated in special milling machines d)The tool used in a sawing process is called a broach
15 1) broaching II) contour turning III) profile milling IV) thread cutting Which of the following above is (are) example(5) of forming the workpart geometry in machining, as opposed to generating the geometry? a) Only I b) I-1I-II-IV C) 1-|1 d) Only II e) II-I|I
Which machine did we used to cut our raw ?material )1 نقطة( Drilling machine O Shaping Machine Band saw machine O Milling machine O
Which one of the given below is/are associated with cemented carbide tools? 26 - Aşağıda verilenlerden hangisi sinterlenmiş karbür takımlarla ilişkilidir? High thermal conductivity A) yüksek termal iletkenlik Good hot hardness B) iyi sıcak tlik All hepsi High elastic modulus D) yüksek elastik modül Good wear resistance E) iyi aşınma dayanımı
40 - Which of the following are not to be considered in machine tool selection?(Aşağıdakilerden hangisi tez O A) Cutting and feedrate settings should be made over a wide range( ma ve ilerleme hiz The machine must be maintenance-free B) -- ltiron türden olm-+ O C) The type of control and the number of service personnel should correspond to the number of parts to be manufactured( u turu ve hizn - - sayısı, ima O D) Themachine tool should be able to be equipped with additional equipment and measuring instruments(T. - UIÇU aleien ne uuiatilabilmelidir) O E) The power of the machine should be suitable for working by removing the thickest chips( nhin niinii an kalın talacı kaldırarak calısmava inun al
Which one of the options isn't classified as a chip form type? a)Non-segmental chip b)Sheared chip c)Discontinuous chip d)Continuous chip
Which of the following infomation about the temperature fomed at the tool-chip interface is wrong?(A hangisi yanlıştır?) 17 - O A) Hat chips can aceste dis advantages in terms of aperstor s sfety (Oluşan s icak talaş. operatör emniyeti açs indan sak ınca oluş turabilin) Decreses tool life(Tak ım ömmünü szaltır ) Apprax imstely 98% of the energy used is converted into hest energy(Ysk laşık kullanı lan enerjinin % 98 i s i enerjis ine dönüşür O D Negstively sifects the size accuracy due to thermal ex pars ion in the wark piece(ş parças inda sil genleşmeden dolay i boy ut has ss iyetini olumsuz yönde etkiler) O E It prevents the risk of brittle fracture on the newly formed surface(Yeni oluşan yüzeyde gevrek kırılma riskini önlemeye yarar)