9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid out with a) parallel lines b) center & center point d) intersecting lines c) perpendicular lines 10) The workpiece is assumed to be already centered when the dial indicator plunger pin touches the whole surface of the workpiece diameter and a) dial indicator b) no deflection on the dial indicator reading c) big deflection on the dial indicator reading d) abrupt change on the dial indicator reading

9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid out with a) parallel lines b) center & center point d) intersecting lines c) perpendicular lines 10) The workpiece is assumed to be already centered when the dial indicator plunger pin touches the whole surface of the workpiece diameter and a) dial indicator b) no deflection on the dial indicator reading c) big deflection on the dial indicator reading d) abrupt change on the dial indicator reading

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To make 200 cast iron tool holders as shown in Figure 2 per order, two orders per year expected, and the inside hole surfaces should be smooth, what manufacturing processes would you suggest for the part. a)Machining processes from the 2X1.5 inch iron bar stocks with no initial tooling cost. cut the bar into 6 inch long pieces with bandsaws mill all the flat surfaces on a milling machine drill the two holes on the same milling machine or a drill press b) sand casting, which has much lower initial tooling cost than die casting and reasonable production rate. drill to make the smooth inside surfaces of the two holes on a milling machine or drill press. c) forging process with rounded edges and corners. drill the two holes on a milling machine or drill press. d)die casting, which can make the part in high production rate with smooth surface and precise dimension
Select all that is true about crosshatching, also known as hatching, hatch lines, and section lines: Group of answer choices Crosshatching is not used over cavities within the cut. Hatch pattern standards exist for ANSI and ISO. Hatch lines indicate cut material that came in contact with the cutting plane. Different hatch patterns represent different materials. Hatch patterns and directions should be identical in adjacent parts within sectioned assemblies. Any hatch pattern can be used.
I need help with parts a,b,c. All three figures are in the corners that align with each problem :)
Moving to another question will save this response. Quèstion 4 In carpentry, the type of saw to be used to work inside a narrow hole or slot is O A. Hack saw O B. Back saw O C. Circular saw OD. None Windows bu Windows buaualic Jaul ENG 4)
please provide the following: speed rate, deep of cut and measurements of a meat mallet.
In section views, match patterns should be drawn parallel to one of the edges of the part. True? A. Yes, always B. Optional C. Never Section views must retain the same scale as the part from which they are created. True? A. Yes, true B. No, they may be scaled
-How many holes require drilling? -What is the center to center distance of the 6mm tapped holes? -What tap drill is used for holes marked Z? -How many surfaces are machine finished? -What are the dimensions of the face marked F & C? -What are the dimensions have symbols A, E &, B -In what dihedral angle is the drawing made? -What is the max and min dimensions of D -What is the tolerance of measurement D?
1.How is the length of a Flat Head or Countersunk, and a Fillister type of machine screw measured?
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.9 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 7 -1.00000 * How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? (Round the final answer to four decimal places.) The depth of the mill should be 7071.067 inches.
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"
Question 3 The Extrude Cut feature in SOLIDWORKS can be used to create both through holes (holes that go all the way through a part) and counter bore holes (holes that do not go all the way through a part), such as the holes shown in the 2-dimensional image below. True False Counterbore
Please show all steps. Using section or integral method is fine. Would be nice to see both but either will work.