Which of the following is not the advantage of Voltage Control by combined On-load Tap-Changing Transformers with off-nominal (t>1) tap locations and Reactive Power (Q) Compensators as shown in the figure below (Fig. Q1): VsZ0 v, 1:t VR ô Pc = 0 PR + jQr Compensator Qc Fig. Q1 Reducing the required Reactive power Compensation (Qc) O Improving the voltage at the Receiving End Improving the voltage stability compared to On-load Tap-Changing Transformers without Reactive Power (Q) Compensators Reducing the active power loss on the transmission line ooo

Which of the following is not the advantage of Voltage Control by combined On-load Tap-Changing Transformers with off-nominal (t>1) tap locations and Reactive Power (Q) Compensators as shown in the figure below (Fig. Q1): VsZ0 v, 1:t VR ô Pc = 0 PR + jQr Compensator Qc Fig. Q1 Reducing the required Reactive power Compensation (Qc) O Improving the voltage at the Receiving End Improving the voltage stability compared to On-load Tap-Changing Transformers without Reactive Power (Q) Compensators Reducing the active power loss on the transmission line ooo

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

Pls answer d. Only
For the circuit in the figure, the source has an amplitude of 2 V and a frequency of 60 Hz. In the experiment, an "Offset of 2 V will be added to it. This produces an effect equal to that of connecting a DC source. 2 V in series with the generator. Present the graph of the voltage across the resistor and capacitor, with and without a DC source in series (this would represent the use of AC coupling and DC coupling). Clearly identify each of the signs. Record amplitude and lag data. Graph only one cycle. + Vin VR R₁ 100 Ω 60 Hz 3 C₁ 220 nF + Vc
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
Vs=16cos100t Volt using T-equivalent circuit for For the circuit shown, find the steady-state 102 voltage "V" and the input power when 100 0.11I V=16cos100t Volt using T-equivalent circuit for transformer. 0.21I 0.211: 50 (Ans.: V=6cos100t Volt & Pin=11.2W)
A single-phase, 60 Hz(input) convertor, such as shown below, operates at a synchronous carrier frequency of 300 Hz, The DC Link voltage is 680 V, and the effective value of the fundamental AC voltage E34 is 430 V. Calculate; 1) The duty cycle D, and Ton when the AC voltage is 500V. 2) The duty cycle D, and Ton when the AC voltage is -30V. 3) Draw the waveform of the convertor output. 5 EL 4-quadrant switching converter EH 2 4 6 D Se
a) For the 2-Bus AC system given in Figure (a) find V1 (amplitude and angle). All the values are given in p.u. Note: Mind complex power concept! b) For the HVDC equivalent circuit given in Figure (b) calculate V2. All the values are given in p.u.
a) Define what the term "permeability" means. Explain why this is an important parameter in designing transformers. b) A maximum current of 60 A flows in a copper conductor with cross-sectional area, A. u7 ond o recistivity of 20 n0. m. A 250 m cable is being used on a 240 V DC circuit to
5 b) What is reactive power compensationExplain how reactive power compensation is made and its benefits.
Please and thank you
Q-3 A Cockeroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 µF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.
Q.2) A 230V, 50 Hz sinusoidal voltage supply is used to provide power to a resistive load via a pair of inverse-parallel connected thyristors. The two thyristors are triggered to give integral-cycle controlled current waveform in the number of conducting cycles N=2 and the total control period T=5 supply cycles. Calculate the supply frequency harmonic voltage and the amplitudes of its immediate harmonic neighbors up to the sixth order harmonic.
A SERIES CIRCUIT CONSISTING OF AN 80- OHM RESISTOR, A 0.30 HENRY INDUCTOR AND A 50-uf (MICROFARAD) CAPACITOR IS CONNECTED TO A 120-VOLT 60+ CYCLE SOURCE C ALCULATE THE FOLLOWINC : (A.) EQUIVALENT IMPEDANC E OF THE CKT, (B.) CURRENT (c.) VOLTAGE DROPACROSS THE SEVERAL UNITS (D.) POWER AND POWER FACTOR,