Which of the below is true for conventional milling: O Chips are removed behind the cutter which reduces the chance of re-cutting Chip width starts from zero and increases which causes more heat to diffuse into the workpiece and produces work hardening Creates cleaner shear plane which causes the tool to rub less and increases tool life

Which of the below is true for conventional milling: O Chips are removed behind the cutter which reduces the chance of re-cutting Chip width starts from zero and increases which causes more heat to diffuse into the workpiece and produces work hardening Creates cleaner shear plane which causes the tool to rub less and increases tool life

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The part in Figure 1 is to be drilled on a turret-type drill press. The part is 15.0 mm thick. Threedrill sizes will be used: 8 mm, 10 mm, and 12 mm, which are to be specified in the part programby tool turret positions TO1, T02, and T03. All tooling is high speed steel. Cutting speed = 75mm/min and feed = 0.08 mm/rev. Use the lower-left corner of the part as the origin in the x-y axissystem. Write the part program in the word address format using absolute positioning.
In an orthogonal machining with a tool of 9 degree orthogonal rake angle, the uncut chip thickness is 0.2mm. The chip thickness fluctuates between 0.25 mm and 0.4 mm. The ratio of the maximum shear angle to the minimum shear angle during machining is
Increase of the cutting speed (Vc) in drilling leads to: Increased chance for tool breakage Higher tool wear Decrease of material removal Which of the described below does not affects the chip forming: Depth of cut Vibrations O Feeding
How can hardened work pieces which cannot be machined with conventional cutting tools be finished machined to precise dimensions with a very smooth surface finish?
A straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel rod. The feed is 0.2 mm/rev and the depth of cut is o.5 mm. The tool has a side cutting edge angle of 60°. The uncut chip thickness (in mm) is .. . ... ...
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
What is the feed speed (mm/min) of an end milling cutter if it mills a distance of 300 mm in ten minutes? What is the feed per tooth if it is rotating at 800 rpm?
Decrease of the cutting feed (Vf) in drilling leads to: a/Harder chip evacuation b/Harder chip breaking c/Better surface finish in the machined hole
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…
Identify the type of milling operation in which the several surfaces of the the workpiece is machined simultaneously. slot milling angular milling gang milling side milling
The tool life equation for HSS tool is VTO.14f 0.7d0.4 = Constant. The tool life (T) of 30 min is obtained using the following cutting conditions: V = 45 m/min, f = 0.35 mm, d = 2.0 mm If speed (V), feed (f) and depth of cut (d) are increased individually by 25%, the tool life
Calculate amount of removed chips in (m³/min), If you have cutting width is 50mm, cutting depth is 10mm and .Feed speed is 4.15 mm/min 1.99 m³/min O 3.099 m³/min 2.075 m³/min O