Examples (homework)1.In orthogonal cutting if the depth of cut is a 1.25 mm and chip thickness aftercutting is 2 mm, determine the following:i.Chip thickness ratio.ii.Shear angle. If rake angle is 10.2.If shear strength is 6000 kg/cm2, width of cut is 10mm, cutting speed is 30m/min, coefficient of friction is 0.9Determine the following:i.Shearing force.•Friction angle.•Cutting force.

As per our guidelines, we are supposed to answer only first one question in case of multiple…

Examples (homework) 1. In orthogonal cutting if the depth of cut is a 1.25 mm and chip thickness after cutting is 2 mm, determine the following: i.Chip thickness ratio. ii.Shear angle. If rake angle is 10.

Examples (homework) 1. In orthogonal cutting if the depth of cut is a 1.25 mm and chip thickness after cutting is 2 mm, determine the following: i.Chip thickness ratio. ii.Shear angle. If rake angle is 10.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a free machining aluminum alloy. Cutting speed = 150 m/min. The nose radius on the tool = 0.75 mm. Determine the feed that will achieve the specified surface finish.
Details pertaining to an orthogonal metal cutting process are given below Chip thickness ratio 0.4 Unreformed thickness 0.6mm Rake angle +10° Cutting speed 2.5m/s Mean thickness of primary shear zone 25 microns The shear strain rate in s during the process is
3.) A 3 inches diameter 5-tooth cemented-carbide-tipped face milling cutter is to use for milling a rectangular shape machine steel workpiece (2-in width x 5 in. length) in a single pass. The cutting speed is 150 ft/min and the feed per tooth is 0.016 in. Determine (a) the feed rate in inch per minute and (b) the cutting time omitting the over travel.
In orthogonal cutting, __________ are independent variables. I. Surface finish of cutting tool;II. Temperature rise in workpiece;III. Depth of cut;IV. Tool holder;V. Cutting force;VI. Stiffness of cutting tool
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
A single-point cutting tool with 12° rake angle is used to machine a steel work-piece. The depth of cut, i.e. uncut thickness is 0.81 mm. The chip thickness under orthogonal machining condition is 1.8 mm. What is the shear angle.
life for minimum cost given that cost of 1 cutting speed is the only variable based on the cutting In a single pass turning operation the cutting time cost and the cutting edge cost. The tool edge is 5, operator wages including the machine tool cost is ? 75/hour and tool life equation is VTO.1 is 100 (a) 10 (b) 17 (d) 36 (c) 29
Do it fast please
A tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10 to 7 deg, Calculate the approximate % change in the life of the tool.
Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.
Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to cut a workpiece of 85 x 42 x 8 cm into two equal parts. The milling cutter is 180 mm in diameter and has eight teeth. Cutting speed = 60 m/min, chip load = 0.35 mm/ tooth, and depth of cut = 2 mm, given that the setup and machine settings provide an approach distance of 7mm before actual cutting begins and an overtravel distance of 20 mm after actual cutting has finished, and the return time is a 4-second for idle pass stroke. Determine:- 1. What is the total machining time required for the entire workpiece? 2. The maximum metal removal rate during cutting.
I need correct answer