answer this question,please * ?Which is correct regarding the shown diagram (13)InputInputInputPowersupplyProcessorAnalogAnalogAnalogIN O OIN O OIN O+IN O-ANL COM OIN 1. eIN 1- OANL COMOIIN 2+ OIIN 2- OIANL COMOIIN 3. 0IN 3-IN O+ OIN O OANI COMOIN 1 0IN 1- 0ANL COMIN 2. eIN 2- OANI COM OIN 1 0IN 1- OANL COMOIN 2IN 2- eL1ANL COMOIN 3. OIN 3- eANL COMANI COMOIN 3. 0IN 3- eANL COM OOL2/NANL COMOGndFlowmeter(0 to 700 GPM range)4-20 mAThe flow meter is connected to the PLC using digital input portsThe signal which is sent by the flow meter varies with time according to the measuredflowThe digital output port that connects the flow meter to the PLC is of the (sinking) type OThe flow meter can be classified as an analog actuatorNone of the answers is correct

The flowmeter is converting the flowrate to 4-20 mA signal, and the measured flowrate varies with…

نقطة واحده ?Which is correct regarding the shown diagram (13) Processor Input Input Input Power supply Analog Analog Analog IN O O IN O O AN COMO IN 1. 0 IN 1-0 ANL COMO IN 2. e IN 2- O ANL COMO IN 3. O IN 3- O ANL COM IN O IN O+ IN O M AN COM! IN O e ANL COMO IN 1 0 IN 1- 0 ANL COM IN 2 e IN 2 ANL COM IN 3 IN 1 IN 1-0 ANL COMI IN 2 eI IN 2- eI ANE COM I IN 3. e! IN 3- e ANL COM ØL1 L2/N ANL COM Gnd Flowmeter (0 to 700 GPM range) 4-20 mA The flow meter is connected to the PLC using digital input ports The signal which is sent by the flow meter varies with time according to the measured flow The digital output port that connects the flow meter to the PLC is of the (sinking) type The flow meter can be classified as an analog actuator O None of the answers is correct

نقطة واحده ?Which is correct regarding the shown diagram (13) Processor Input Input Input Power supply Analog Analog Analog IN O O IN O O AN COMO IN 1. 0 IN 1-0 ANL COMO IN 2. e IN 2- O ANL COMO IN 3. O IN 3- O ANL COM IN O IN O+ IN O M AN COM! IN O e ANL COMO IN 1 0 IN 1- 0 ANL COM IN 2 e IN 2 ANL COM IN 3 IN 1 IN 1-0 ANL COMI IN 2 eI IN 2- eI ANE COM I IN 3. e! IN 3- e ANL COM ØL1 L2/N ANL COM Gnd Flowmeter (0 to 700 GPM range) 4-20 mA The flow meter is connected to the PLC using digital input ports The signal which is sent by the flow meter varies with time according to the measured flow The digital output port that connects the flow meter to the PLC is of the (sinking) type The flow meter can be classified as an analog actuator O None of the answers is correct

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

can ou please answer question d?
please solve question number 2,3,4,5
Can you please further explain how you used the ID equation to find the solution? Thank you
Use the block diagram reduction please
Please click on pic to open it
please explain with fully details
PLEASE ANSWER BOTH QUESTIONS FOR UPVOTES. NO UPVOTE IF ONLY ONE HAS AN ANSWER. PUT ONLY BRIEF EXPLANATIONS ON CHOOSING THE CORRECT ANSWERS. THANK YOU
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please no plagiarism and must be in your own words (400 Words) LIST THE BENEFITS OF RENEWABLE ENERGY (RE) PROGRAMS FOR A COUNTRY.
Can you help me with these problems?