When conducting no-load test on a given single-phase transformer, the following test data were obtained : Primary voltage : 230 V ; Secondary voltage : 110 V ; Primary current : 0.5 A ; Power input : 35 W. Find (i) The turns ratio (ii) the magnetizing current of no-load current (iii) Core loss current (iv) the iron loss.

When conducting no-load test on a given single-phase transformer, the following test data were obtained : Primary voltage : 230 V ; Secondary voltage : 110 V ; Primary current : 0.5 A ; Power input : 35 W. Find (i) The turns ratio (ii) the magnetizing current of no-load current (iii) Core loss current (iv) the iron loss.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Blue is the numerical answer, I need a detailed solution.
What are the advantages and disadvantages of back to back test on two similar single phase transformer?
Q3/The core of a 300-kVA, 15000/650 V, 50-Hz, 1-ph, core type transformer has across- section of 30 cm × 30 cm. Find (i) the number of H.V. and L.V. turns per phase and (ii) the e.m.f. per turn if the maximum core density is not to exceed 1.5 Tesla. Assume a stacking factor of 0.75.What will happen if its primary voltage is increased by15% on no- load ?
Draw the general diagram of a single-phase transformer and briefly show how it works.
answer: 5.19 – j2.95 A
(9) The hysteresis losses in electrical machines reduced. a- By core lamination. b- By core isolation. c- By choosing another type of iron. (10) The eddy current losses in electrical machines reduced. d- By core lamination. e- By core isolation. f- By choosing another type of iron.
Q1: During the separation of transformer core losses experiment: 1. Why should always keep the ratio of V/F constant? 2. If the transformer is operated at rated frequency but at voltage lower than rated value, how do you expect the following quantities to change? And why? i. Hysteresis loss ii. Eddy current loss iii. No-load current rotod
When conducting no-load test on a given single-phase transformer, the following test data were obtained : Primary voltage : 235 V ; Secondary voltage : 110 V ; Primary current : 0.5 A ; Power input : 35 W. Find (i) The turns ratio (ii) the magnetizing current of no-load current (iii) Core loss current (iv) the iron loss. Turns ratio The magnetizing current of no-load current Core loss current Core loss
5. Transformer cores are laminated in order to (a) simplify its construction (b) minimise eddy current loss (c) reduce cost (d) reduce hysteresis loss. 6. A transformer having 1000 primary turns is connected to a 250-V a.c. supply. For a secondary voltage of 400 V, the number of secondary turns should be (a) 1600 (b) 250 (c) 400 (d) 1250 7. The primary and secondary induced e.m.fs. E, and E₂ in a two-winding transformer are always (a) equal in magnitude (b) antiphase with each other (c) in-phase with each other (d) determined by load on transformer second- ary. 8. A step-up transformer increases (a) voltage (b) current (c) power (d) frequency. F
Q8 Complete the answer : A core type transformer operates on 410 / 225 volt, 50 Hz supply. If the cross-sectional area of the core is 30 cm? and maximum flux density is 1.1 Wb/m?, then the number of turns in secondary winding will be...............
A transformer core is laminated in order to ....................................? (A) reduce hysteresis loss and eddy current loss (B) reduce only hysteresis loss (C) reduce copper loss (D) reduce all of the above losses (E) None of the above.
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no- load voltages in the primary and secondary circuit are 200 and 400 volts, respectively, and at a frequency of 50 Hz. The primary no-load current at a voltage of 200 volts is 0.7 amps and the losses in the core are 70 watts. The resistance and reactance of the primary are 3.2 and 1.25 ohms, respectively. Secondary resistance and reactance 6. 0, 0.07 ohms, respectively. Draw the equivalent circle, showing the values of its elements.