When conducting no-load test on a given single-phase transformer, the following test data were obtained :Primary voltage : 205 V; Secondary voltage : 115 V;Primary current : 0.7 A; Power input : 35 w.Find (1) The turns ratio (i) the magnetizing current of no-load current (ii) Core loss current (iv) the iron loss.Turns ratioThe magnetizing current of no-load currentCore loss currentCore loss

Answered: Image /qna-images/answer/52b1dfd0-297d-47aa-94ba-7abca6070652.jpg

When conducting no-load test on a given single-phase transformer, the following test data were obtained : Primary voltage : 205 V: Secondary voltage:115 V: Primary current : 0.7 A; Power input : 35 w. Find () The turns ratio (ii) the magnetizing current of no-load current (ii) Core loss current (iv) the iron loss.

When conducting no-load test on a given single-phase transformer, the following test data were obtained : Primary voltage : 205 V: Secondary voltage:115 V: Primary current : 0.7 A; Power input : 35 w. Find () The turns ratio (ii) the magnetizing current of no-load current (ii) Core loss current (iv) the iron loss.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1: During the separation of transformer core losses experiment: 1. Why should always keep the ratio of V/F constant? 2. If the transformer is operated at rated frequency but at voltage lower than rated value, how do you expect the following quantities to change? And why? i. Hysteresis loss ii. Eddy current loss iii. No-load current rotod
When conducting no-load test on a given single-phase transformer, the following test data were obtained : Primary voltage : 235 V ; Secondary voltage : 110 V ; Primary current : 0.5 A ; Power input : 35 W. Find (i) The turns ratio (ii) the magnetizing current of no-load current (iii) Core loss current (iv) the iron loss. Turns ratio The magnetizing current of no-load current Core loss current Core loss
5. Transformer cores are laminated in order to (a) simplify its construction (b) minimise eddy current loss (c) reduce cost (d) reduce hysteresis loss. 6. A transformer having 1000 primary turns is connected to a 250-V a.c. supply. For a secondary voltage of 400 V, the number of secondary turns should be (a) 1600 (b) 250 (c) 400 (d) 1250 7. The primary and secondary induced e.m.fs. E, and E₂ in a two-winding transformer are always (a) equal in magnitude (b) antiphase with each other (c) in-phase with each other (d) determined by load on transformer second- ary. 8. A step-up transformer increases (a) voltage (b) current (c) power (d) frequency. F
Q8 Complete the answer : A core type transformer operates on 410 / 225 volt, 50 Hz supply. If the cross-sectional area of the core is 30 cm? and maximum flux density is 1.1 Wb/m?, then the number of turns in secondary winding will be...............
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuits are 200,400 volts, respectively, at a frequency of 50 Hz The primary no-load current at voltage 200 equals 0.7 amps and pulp losses equal to 70 watts Primary resistance and reactance 3.2 , 1.25 In order, the reactance of the resistance and the coil 0.6 , 0.7 Then draw the equivalent circle, explaining the values
During the load test of single-phase transformer, when the secondary terminal voltage increases, the regulation of the transformer will ................?(complete)
- A Transformer has primary windings as Np = 750 and secondary windings as Ns = 125. Its secondary voltage is Vs = 36V and output power of the transformer is PN= 3200W. The value of loses powers are Pcu = 43W and Pfe = 29 W. The resistance of loads are RLI = 1,250 and R12 = 0,88Q. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit: Primary winding N, turns Secondary winding Ng turns Primary current Magnetic Flux, Secondary IsL s current ISL1 'Isl2 Primary voltage Secondary voltage RL1 R12 Transformer Core (a) the primary voltage Vr, (b) the secondary load currents ISLı and Isl2 if the transformer is rated at RLI and R12, (c) the resulting secondary power PSL, (d) the resulting primary power PPl, (e) the primary load current IPL, (f) efficiency nL
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
E In a transformer, the core loss is found to be 52 W at 40 Hz and 90 W at 60 Hz measured at same peak flux density. Compute the hysteresis and eddy current losses at 50 Hz.
b) The parameters of the transformer equivalent circuit are given bellow, Primary =1290. Secondary winding turns =130. The resistance of the primary winding =0.2 O. The resistance of the secondary winding =0.06 N. The leakage reactance of the primary winding =1.47 Q. The leakage reactance of the secondary winding =0.07 Q. using the above parameter values, referred to the primary winding, determine (a) Equivalent resistance, (b) Equivalent reactance, (c) Equivalent impedance and (d) The phase angle of the impedance.
Q1: During the separation of transformer core losses experiment: 1. Why should always keep the ratio of V/F constant? 2. If the transformer is operated at rated frequency but at voltage lower than rated value, how do you expect the following quantities to change? And why? i. Hysteresis loss ii. Eddy current loss iii. No-load current
Consider the following open circuit transformer as shown in figure below which operate at: the voltage sources at no load (Voc)=170 V no load current (Ioc) = 85 m A iron losses power (Poc) = 14 W power factor = cos∅= 0.968 Compute the No load transformer parameter magnetizing (Im) and copper losses current (Ic) , (R0) and (X0) ?