When a bar is cooled to -5°C, it will developO(A) No stressOCB) Shear stressOC) Tensile stressO(D) Compressive stress

When bar cooled down it is getting contracted or try reduce its length . But Everybody try to…

Answered: When a bar is cooled to -5°C, it will…

When a bar is cooled to -5°C, it will develop O(A) No stress O(B) Shear stress OC) Tensile stress O(D) Compressive stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stresses in a flat steel plate in a condition of plane stress are: o, = 10000 N/mm2 o = 6000 N/mm? = 8000 N/mm2 Find the magnitude and orientation of the principal stresses in the plane of the plate.
A steel rod Is stretched two rigid walls and carries a tensile load of 6000 N to 20°C. Coefficient of thermal expansion a = 11.7 x 10-5 /C and modulus of elastičity 200000 MPa. 7. Which of the following gives the minimum diameter of the rod if the allowable stress is not to exceed 140 MPa at -25°C. a. 15 mm C. 16 mm b. 17 mm d. 18 mm 8. Which of the following gives the total elongation of the steel rod if it has a length of 1.5m. a. 1.00 mm С. 1.02 mm b. 1.04 mm d. 1.06 mm 9. Which of the following gives the strain of the steel rod. a. 0.00067 b. 0.00071 C. 0.00069 d. 0.00073
(c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm² stress.
Current Attempt in Progress A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 200mm and the wall thickness is 13mm. If the air in the tank is pressurized to 18.2MPa, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: (a) long Thoop= (c) Tabs max= i i i MPa MPa MPa MPa
Solution.
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 225 mm, a wall thickness of 7 mm, and a length of 5.9 m. The pipe supports a compressive load of 690 kN. After the temperature of the pipe drops 50°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
1) The plastic polymer cylindrical pipe is carrying flowing water at 0.5 N/mm pressure. The pipe has open ends. The inner diameter of the pipe is 0.1 m. The thickness of the pipe is one tenth of the pipe's inner radius. Calculate the stresses to show the state of stress in the walls of this pipe. (Suggested time for solution is 15 minutes)
A high-density polyethylene [E = 121 ksi and a = 61 x 10-6/°F] block (1) is positioned in a fixture. The block is 2.2 in. by 2.7 in. by 29 in. long. At room temperature, a gap of 0.11 in. exists between the block and the rigid support at B. Determine: (a) the normal stress o in block (1) caused by a temperature increase of 98°F. (b) the normal strain & in block (1) at the increased temperature. [ Answerrs: (a) o = (b) = 0.11 in. 29 in. Ans: (a) - 264.3725 με. (b) 3793.1033 psi.
A round vertical steel tank has an inside diameter of 3.5 m and is 8 m in height. It containsgasoline with specific gravity of 0.8. If the allowable tensile stress is 24 Mpa, find theminimum thick required.
At an axial load of 25 kN, a 50-mm-wide by 15-mm-thick polyimide polymer bar elongates 3.1 mm while the bar width contracts 0.26 mm. The bar is 220 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E- (b) v- (c) Audness GPa mm
asap
4. A titanium alloy (Ti-6Al-4V) pipe has a bronze C86100 copper alloy core and is subjected to a force, P = 150 kN. Determine the average normal stress in each material and the elongation if the pipe has an outer diameter of 90 mm and an inner diameter of 70 mm. (Solution: On = 25.789 MPa, 22.135 MPa, 8 = 0.086 mm) 400 mm-