what the name of the coordinate system defined by Reference plane, Cutting edge plane, and Orthogonal plane?

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the x-axis (θx)? Note that…

A:

Q: Draw the orthographic view of the following component mention top view ,side view,front view

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: What is a polar coordinate system

A: In arithmetic, the polar coordinate system could be a two-dimensional arrange framework in which…

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: Can you please send me top,front and right view of the given diagram with correct dimensions.

A: The isometric view is given in the diagram.

Q: Creste an sometre ptora and thena caet ut l the folloing abject. The grid soacing is 10 mm.

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the z-axis (θz)? Note that…

A:

Q: Pls provide the sectional view below

A:

Q: Problem 1 For the 3d object shown to the right, complete the following: a) Determine the position…

A:

Q: Question 1 A point P(6,1,2) that is attached to a frame is subjected to the followings sequence of…

A: We have point P= [6 1 2] In 3D, we take it as P= [6 1  2 1] Then we apply given transformations…

Q: 1. Sketch the CAVALIER OBLIQUE of the given object. Use corner "A" for orientation.

A: according to the details provided in the question, we need to draw a cavalier view of the given…

Q: R 19- $10 LJØ20 T6 19 38 63 76

A: The hand drawn third angle projection of top view, front view and side view is given below.

Q: for the given figure , draw the 2d sketch using AutoCad and give the dimension

A:

Q: This prelab question is about the experimental setup shown in the Lab Manual as Figure 1 for…

A: In theory we assume ideal conditions (that are not practical or applicable in real world). Hence…

Q: Can you send me the top, front and right view of the given diagram with correct dimensions

A: The isometric view is given in the diagram.

Q: Can you send me the top,front and right view of the given diagram with correct dimensions

A: Draw the top,front and right view of the given diagram with correct dimensions.

Q: QI: Draw the orthographic Projections of given object. 20, 26 20 14 R20 35 SHOT ON REDMI 7 AI DUAL…

A: Orthographic projection is a two-dimensional representation of three-dimensional objects. It's a…

Q: 2 link 1 Draw HGL & EGL. tankz tank 3

A: For the solution refer below images.

Q: I just need help drawing the KINEMATIC DIAGRAMand the GRAPHS (v-a, a-s, s-t, v-t, v-t, or a-t) if…

A: Given: The v-s diagram is shown below: From distance 0 to150 m, the equation of velocity line is…

Q: Find the absolute coordinates, relative coordinates, and polar coordinates. (AutoCAD) GIVEN:…

A: It is asked to find the absolute, relative and polar coordinates of the corners shown below

Q: Sketch the 2D figure of cover using AutoCAD and mention all the dimensions, colour the hatched lines…

A:

Q: Basic Conversions A solid flat disk is rotating in the counter-clockwise (or positive) direction.…

A: givenobject is at a distance r=1.3mangular velocity when θ=0, ωo=4rad/safter t= 1.57sec angular…

Q: The mechanism shown in figure below has been taken from a feed device for an automated ball bearing…

A:

Q: What is relative position vector?

A: A vector is defined as a quantity that always has two properties - a magnitude and a direction and…

Q: State any three rules of orthographic parallel projection.

A: Orthographic parallel projection is a method of representing 3D objects normally by three 2D…

Q: Draw the left view of the component and the projections of all the points.

A: given views  top and front view  to draw the left view and name the

Q: robotics axis and frames   I am trying to define the axis at each joint, x, y z and whether into…

A: INTRODUCTION : Translations and rotations are based on frames, which are the static coordinate…

Q: 4. The vertical plate ABED is pinned to rod OA at A and supported by a roller at E which slides in a…

A: according to the given details

Q: D 450 15° 30 kg 30 mass 13 FIG - B3

A: As per above given FBD we can sayT1=mgT1=30×9.81T1=294.2 NHere T1=FCDFCD=294.2 N

Q: -AB cos(T/3) + AC + Ax = 0 -AB sin(7/3) + Ay = 0 AB cos(7/3) – BC cos (T/3)- BD = 0 AB sin(T/3) + BC…

A: Unknowns : AB AC BC BD CD CE DE Ax Ay Ey In vector form → KX = B where K = coefficient matrix…

Q: draw the orthogonal projections of the displayed object

A: According to the details provided in the question, we need to draw three projection views.

Q: . Draw it's projections in all possible positio

A: Given: A point is 50 mm from both the reference planes. To determine: Projections in all possible…

Q: The base structure of the firetruck ladder rotates about a vertical axis through O with a constant…

A:

Q: Car A is traveling at the constant speed of 47 km/h as it rounds the circular curve of 245-m radius…

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.