What surface imposes little or no shear stress on the fluid? A B C OB

Q: Refer to Fig. 9-36. The angle of static friction between the block with mass M and the plane is d.…

A:

Q: Part A FDE = Value Submit HÅ Part B 2 m Request Answer 2 m 2 2 m Determine the magnitude of the…

A: Part ADetermine the magnitude of the component of F = 600N acting along to segment DE of the pipe…

Q: Define hydrostatic stress state.

A: Solution: It is defined as the state in which stresses of the same magnitude and direction are…

Q: The change in length takes place in the opposite direction of action of external load is known as…

A: When a body subjected to an external load then a linear strain occurs in the direction of opposite…

Q: 4. Biot hypothesized that the shear modulus is influenced by the presence of the pore fluid. 5. Pure…

A: The given questions are : 4. Biot hypothesized that the shear modulus is influenced by the presence…

Q: If a tire has a contact patch length of 104 mm, and is braking at 0.08 slip longitudinally across a…

A: The longitudinal slip of a tyre is the difference between the tangential speed of the tyre and the…

Q: VQ/lt can not be used to calculate the shear stress distribution of a

A: Given, It is asked about the validation of shear stress distribution for given area

Q: -Which of the following statement/s is NOT true? Strain is dimensionless The cross-sectional area…

A: It is required to choose correct option

Q: An airplane has a half-wingspan of 29 m. Determine the change in length of the aluminum alloy [x =…

A:

Q: surface roughness R. (in um) is a

A: Given; Assume that the surface roughness profile is triangular as shownschenatically in the figure.…

Q: The frame shown could be subjected to a variety of loads applied at different points. Consider the…

A:

Q: 2) The change in temperature that causes a brass rod to increase in length from 900 mm to 900.2mm is…

A:

Q: Q1 /Draw S.F.D and B.M.D 20 N/m 100 m 3m 1m 6m Gm Shear Force Diagram S.F.D B.M.D

A: Given Data The UVL acting on the beam is: 50 kN/m The UDL acting on the beam is: 20 kN/m The…

Q: When the fluid at rest the shear stress is zero Select one: True False

A: When the fluid at rest the shear stress is zero. Answer: True

Q: An example of a liquid lubricant is crude base that is introduced between two contact surfaces to…

A:

Q: The oil sump's small external surface area helps heat transfer from the oil to the outside air.…

A: Oil sump is used in 2 stroke and 4 stroke engines to cool the engine oil when its temperature…

Q: List the static and dynamic properties of fluids?

A: Static properties of the Fluid are properties which are calculated when the fluid is at rest.…

Q: Define the shear and bending-moment diagrams.

A:

Q: When the width of the elliptical hole in a flat plate approaches zero in the direction of load, the…

A: This question is from machine design

Q: Where should the internal resultant shear force be directed?

A: Direction for the internal resultant shear force will be opposite to the net force acting on the…

Q: how to calaculate  the strain energy

A: There are two main ways to calculate strain energy, depending on the given information:  Using force…

Q: Find wark done F = 2.221N d=1-22m

A: Given data : Force=F Displacement=d   Required : Work done

Q: If the principal stresses and maximum shear stress are of equal numerical value at a point in a…

A: The principal stresses and maximum shear stress are of equal magnitude at a point in a condition…

Q: As shown in the figure, the forces P1 and P2 are applied to the end A of the rod AB welded to the…

A:

Q: etermine the absolute maximum shear stress.

A: Given that ,  σxx=-79.7 MPaσyy=50.5 MPaτxy=-24.9 MPa

Q: 8- When the sum of the forces acting on a particle is zero, the adjustment will be very large. O…

A: When the sum of forces acted on a particle is zero then the particle is in equilibrium. According to…

Q: HaW: Find the tensian force in each eable. 35 木 A. oss م لملعنه سسلمیڈک the pully te Kep the system…

A: 1) Solution: Consider joint 1 Considering system in static equilibrium,…

Q: A mild steel material is subjected to a Brinell hardness test with an applied force of 7722 N using…

A:

Q: Data: P = 2 kip d = 3.6 inch w = 305 millimeters t = 0.03 meter r = 5.08 centimeter h = 0.6667 feet…

A:

Q: Given D 2KN ← 1m P 2 To Determine 0-3 1m (1-7 one • Diameters of the bars is 1mm e 3 3KN Youngs…

A: Consider elements connecting nodes 1 and 2 as Element-I and element connecting nodes 2 and 3 as…

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: Which of the following statement is/are correct? (please select MORE THAN one answer) Radius of a…

A: Given:

Q: Sketch the distribution of shear stress across the diameter of the blood vessel.

A: It is asked to sketch the shear stress distribution in blood flowing through a blood vessel

Q: How can the direction of shear flow be established?

A: In solid mechanics, the shear flow is defined as the flow when the transverse shear force acts on a…

Q: z=(x-a} +n(y+b)° 8. Consider the following statements (which statement(s) is/are correct): =2,…

A:

Q: Explain the difference between Newtonian and non -Newtonian fluids using the graph shear stress vs…

A:

Q: What would be the Technique to find the value of 'd' in this equation? I mean Show the…

A:

Q: What force is required to punch a 20-mm-diameter hole in a plate that is 25 mm thick? The shear…

A:

Q: ery quickly to solve this que

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.