What is type-l settling? How analysis of type-l settling is done? Find the settling velocity of a discrete particle in water having diameter 4 x 10-3 cm and specific gravity 2.65. Take kinematic viscosity of water = 1.02 x 10-2 cm²/sec.

What is type-l settling? How analysis of type-l settling is done? Find the settling velocity of a discrete particle in water having diameter 4 x 10-3 cm and specific gravity 2.65. Take kinematic viscosity of water = 1.02 x 10-2 cm²/sec.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider particles in suspension and their settling behaviour at different concentrations select the correct statement(s). Type 1 settling is called discrete settling. Your option is Correct B Terminal velocity in suspension is achieved when drag force is balanced by gravity force. Your answer is IN-CORRECT Correct Option 24 In Type 1 settling, for Ree(100, 300) Cp = +0.34 (Re = Reynold's number) Re VRe D In Type 2 settling, the velocity of floc does not remain terminal and keeps changing as the size of the floc changes. Your option is Correct
What is the settling velocity of a discrete particle in a wide body of water when the relevant Reynolds number is less than 0.5? The diameter and specific gravity of the particle are 2 x 10-3 cm and 2.65, respectively. Water temperature is 20°C. (Kinematic viscosity = 2 x 10-2 cm²/ sec.)
A setlling chamber is used to remove sand and grit from the influent water to a wastewater treatment plant. Conditions are: Chamber Height = 3m Chamber Width = 2m Chamber Length = 7m Water Flow Rate = 0.5m3/min Particle Density = 2.65g/cm3 a) What is the minimum settling velocity required for a particle to be required for a particle to be removed by this setlling chamber? Express your answer in units of cm s-1. b) Assume that this or another setlling chamber removes all particles having settling velocities greater or equal to 0.04 cm s-1. What is the minimum particle diameter that would b e entirely removed by such a setlling chamber? Express your answer in units of micrometers. (For part (b), assume the particle being removed is approximately spherical, and the water is at 22°C (density = 997.7 kg/m3, dynamic viscosity = 0.957x10-3 kgm-1s-1). If you use Stoke’s law as part of your solution, be sure to use the Reynolds number to confirm you are in the laminar flow range.)
Subject soil Mechanics
Permbility. K.
Estimate the terminal settling velocity in water at a temperature of 15°C of spherical silicon particles with specific gravity 2.4 and average diameter of 0.05mm. Assume p=999 kg/m3 and p= 0.00113 Ns/m2
Read the question carefully and give me right solution. Provide detailed solution with clear calculations. The hydraulic conductivity of a soil sample, measured at 25C, was 0.005 cm/s using water as the test fluid (density = 997.2 [kg m–3 ], viscosity = 0.0008872 [kg m–1 s –1 ]. Determine the conductivity for ethanol at 10C, density = 798 [kg m–3 ], viscosity = 0.001394 [kg m– 1 s –1 ]
Which of the following is not a mode of field flow fractionation? a. Viscosity b. Sedimentation c. Flow d. Thermal
1.4 A test for the relative density of soil in place was performed by digging a small hole in the soil. The volume of the hole was 400 ml and the moist weight of the excavated soil was 9 N. after oven drying, the weight was 7.8 N. Of the dried soil, 4N was poured into a vessel in a very loose state, and its volume was found to be 270 ml. The same weight of soil when vibrated and compacted had a volume of 200 ml. Determine the relative density.
please show all your solutions dont shortcut it please answer it by week with complete solutions then after put it in a table form
In a water treatment, the temperature of water is 20°C. The diameter of the solid particles present in water is 0.05 mm and have specific gravity of 1.2. Determine the settling velocity of the partiles if the kinematic viscosity of water is 1.01 cSt.
SITUATION 3. Following are the results of a sieve analysis. SIEVE NO. OPENING (mm) RETAINED 4 4.75 10 2.0 40 20 0.85 60 40 0.425 89 60 0.25 140 80 0.18 122 100 0.15 210 200 0.075 56 PAN 12 a. Find the effective particle size. b. Determine the uniformity coefficient. c. Find the coefficient of curvature.