What is the x-coordinate, x1, and y-coordinate, y1, of shape 1’s centroid? (Whole semi-circle, do not consider the square area) e) What is the x-coordinate, x5, and y-coordinate, y5, of shape 5’s centroid? (Whole semi-circle, do not consider the square area) f) What is the x-coordinate, x2, and y-coordinate, y2, of shape 2’s

Q: Locate the centroid Y of the plane area shown in mm from the coordinate axes. r = 72 mm. Write…

A:

Q: 1-2in. -1in-+1int Hin 3in- T 3in 2in

A:

Q: Calculate the coordinates of the polygon

A: Data given Find : coordinates of the polygon

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: 150 mm Locate the centroid of the coloured area. 50 mm 100 mm 100 mm

A: Marking points over figure- A, B, C, D, E, F In the fig three shapes can be observed clearly- 1.…

Q: 100 mm 150 mm

A:

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: LOCATE THE CENTROID OF THE PLANE AREA SHOWN

A: To find centroid

Q: For the body below, determine the centroid under the reference frame shown. Y 2

A:

Q: Calculate the coordinates of points B and C of the connecting polygon

A:

Q: Given the following information Distance Azimuth (m) Course Bearing Latitude Departure N 60°00' W…

A: Answer:- Latitude and Departure:

Q: Is sigma xy horizontal and sigma xz vertical

A: Reference: wikimedia commons

Q: Show me this drawing Step by step how to draw it. thank you 25 105 30 ø16 60° 40 60 70 it's from…

A: To Determine Steps to be used in drawing the given figure in CADD software.

Q: 12 10 1 7. 14 16 18 11 2 8. 13 17 15

A: A truss is given in the question and it has been asked to determine external and total…

Q: 4. Complete the third projection of the plane ABC. Z -Yw Y₁ W X- a a b' C O 45° YH

A: Third projection of plane ABC is draw using projecting the line from abc and a'b'c'.

Q: 3. The accompanying figure shows a network of one- way streets with traffic flowing in the…

A: The volume of data that passes through a network at any particular time is known as network traffic.…

Q: Determine the cross sectional area of the given cross section notes: LEFTMOST LEFT CENTER RIGHT…

A:

Q: Please do Part C, E, and F

A: To solve part C,E and F

Q: What are the radius and center of the following circle? x2 + y2 + 4x – 4y + 4 = 0

A: The given equation of circle is, x2+y2+4x-4y+4=0

Q: The bent bar structure ACDE is supported by ball-and-socket joint at A and E, and by the wire DF.…

A: Given:- A ball-socket-joint is provided at point A The magnitude of the load (P) = 640 N  The…

Q: Correctly Dimension the object using datum dimensioning

A: To show the datum referencing of the drawing

Q: Hydraulic Radius Determine the general expression for the hydraulic radius of a circular pipe…

A: It is asked to determine the expression for Hydraulic Radius of a circular pipe when it is fully…

Q: Find

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 16 35 +…

A:

Q: Situation 2: The hydraulic conductivity of a soil sample was determined in a soil mechanics…

A:

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: g) What is the x-coordinate, x4, and y-coordinate, y4, of shape 4’s centroid? h) What is the…

A: g) What is the x-coordinate, x4, and y-coordinate, y4, of shape 4’scentroid?h) What is the…

Q: LOCATE THE CENTROID OF THE PLANE AREA SHOWN

A:

Q: 20 cm 2o cm 40 cm 40cm 20cm 80 cm

A:

Q: Locate the centroid (x̄, y̅) of the cross-sectional area.

A: Consider the figure,

Q: Find the centroid of the following cross-sections and planes.

A: Centroid is = (0, 9.427 in)Explanation:Step 1: Calculation for centroid of given section.Thanks.

Q: The tensions in the supporting cables AC and BE are 50N and 70 N. respectively. A load of 10 kg is…

A:

Q: Part a and part b

A: Given data in question Load wSpan LCantilever beamInner radius 50 mmThickness 10 mmLongitudnal…

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: What is FB in N? What is the angle FB in degrees? What is FA in N?

A:

Q: Problem 1 Determine the coordinates of the centroid of the given area. 6" y 3" 3" 4.5" ity #

A: To determine: Centroid of the given area.

Q: Determine the cross sectional area of the given cross section notes: LEFTMOST LEFT CENTER RIGHT…

A:

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.