The bent bar structure ACDE is supported by ball-and-socket joint at A and E, and by the wire DF. Determine the distance d where the 640N load should be applied so that the tension in the wire DF does not exceed 342,86 N.

Q: the differences between CAD, CAE, CAM and CIM.

A: CAD:- Computer-aided design is defined the practice of using the computer systems in order to help…

Q: 2. Determine the x and y coordinates of the centroid of the section shown. 450 mm 720 mm K 150 mm…

A: Given data in question  Axis system Dimensions  Quarter circle 300 mm radius Triangle with base and…

Q: Draw orthographic views of the figure with dimensions

A: The isometric view the three dimensional which is drawn in the two dimension.  The orthogonal view…

Q: Additional Problem #2 30 mm Locate the centroid of the cross-sectional area at right. Sketch the…

A: The given figure is shown below:

Q: lgorithm for drawing this in CAD.

A: please follow steps.

Q: III-3 BASIC STANDARDS IN TECHNICAL DRAWING III-3-1 Formats These are. on which are executed the…

A: To fill the blanks in the given question.

Q: A W24x62 beam (Cb = 1) spans 24 ft and is braced at the ends and middle. Determine Mn.

A: Answer  From table AISC 1-1. W shape properties we have for W 24 x 62  Zx = 153 mm3  Sx = 131 mm3…

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the 2D Orthographic Projection (Front,…

A: Asked: To draw the orthographic projections of the given object.   The following tools are used to…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Write the IUPAC name for   compound.

A: International Union of Pure and Applied Chemistry (IUPAC)) is the naming pattern or nomenclature…

Q: Find the vertical and horizontal line detect segmentation

A: Detecting vertical and horizontal lines in an image is a common task in image processing and…

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: For any engineering example discuss with drawing the Bathtub Curve

A: The bath tub curve is generally used in reliability engineering.   This curve signifies the…

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: Identify the several types of lines used in drawing and explain their uses

A: To list different types of lines used in engineering drawing

Q: What size will it be if 4" is at scale 2"=1"

A: Given tha scale  2"=1" Thus defines the sclae ratio  for a drawing is 2:1. Scale ratio = drawing…

Q: Each of the following parts was created with one feature. Name the Base feature for each part.…

A: Base feature : It is called as starting feature before creating an object. 2D geometry : It is 2…

Q: draw the front view, side view, and top view

A: Isometric view is given. We need to draw front view, side view and top view

Q: e shape factor for the section as shown -3d 3d - fe 2d

A:

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: Solution:- At first show the starting point of 20.20 then inclined upwards with the base, make an…

Q: It is allowed to dimension to concealed lines. Do you believe this or not?

A:

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: can you show the sides with dimensioning

A: To show the sides with dimensioning

Q: What are the types of coordinate system? Illustrate with neat figure.

A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate.  Cartesian…

Q: Define Class 1 and 2 of cross sections

A: Class 1 cross-sections are those which can form a plastic hinge with the rotation capacity required…

Q: graphical presentation for 3D shearing transformation.

A: It is change looking like the article. It is likewise called as deformity. Change can be in the x -…

Q: 25 35 55 60 15 30 140

A: Front viewSide view and top view

Q: top view and isometric/oblique drawing of the given figure

A: TO draw the top view and Isometric View