What is the volumetric flow rate through at 4 inch (10 cm) diameter pipe containing chocolate milk (p= 1010 kg/m³, µ = 0.00202 Pa.s). Along this section of pipe, there are two 90° pipe bends (K = 0.2) and a fully open gate valve (K = 0.1). The average roughness height of the pipe is ɛ = 0.1 mm. You measure the pressure at the two gauges shown below and find that the pressure decreases between them by 802.8 kPa. %3D 1m- Valve -1m- What is tbe volumetric flow rate through this section of pining?

What is the volumetric flow rate through at 4 inch (10 cm) diameter pipe containing chocolate milk (p= 1010 kg/m³, µ = 0.00202 Pa.s). Along this section of pipe, there are two 90° pipe bends (K = 0.2) and a fully open gate valve (K = 0.1). The average roughness height of the pipe is ɛ = 0.1 mm. You measure the pressure at the two gauges shown below and find that the pressure decreases between them by 802.8 kPa. %3D 1m- Valve -1m- What is tbe volumetric flow rate through this section of pining?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4) In the system below, pipe A has a diameter of 6", a length of 1500 ft and a friction factor of…

A: Given Parallel pipesVelocity in pipe B 5 ft/sLengths of A and B = 1500 and 1000 ftDiameter of A and…

Q: Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section…

A: Given- Head difference between point 1 & 2 = 1.5 m, Discharge Q=0.9 m3/s, Diameter at section 1…

Q: Calculate the pressure difference between the 2 points shown on the figure below (P1 - P2)? Fluid in…

A: Given :- The pressure difference between 2 points ( P1-P2) SG =13.6 Cross-…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

Q: In a pipeline with a diameter of 500mm, a venturi meter is installed. The ratio of the throat pipe…

Q: Ex. For the square loop shown: 1. find the discharge in all the pipes. All pipes are 1 km long and…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: The pressure heads are measured at two sections in a pipeline and are found to be 8.3 m at point A…

A: Step 1: Step 2: Step 3: Step 4:

Q: A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

What is the volumetric flow rate through at 4 inch (10 cm) diameter pipe containing chocolate milk p =
1010 kg/m³, u= 0.00202 Pa.s). Along this section of pipe, there are two 90° pipe bends (K = 0.2) and a
fully open gate valve (K = 0.1). The average roughness height of the pipe is ɛ = 0.1 mm. You measure
the pressure at the two gauges shown below and find that the pressure decreases between them by
802.8 kPa.
-1m-
Valve
-1m-
What is the volumetric flow rate through this section of piping?
-6→

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Suppose that a = 1.96 m and b = 1.4 m. (Figure 1) Figure y = x¹/2 < 1 of 1 Part A Determine the moment of inertia for the shaded area about the axis. Express your answer to three significant figures and include the appropriate units. I₂ = Submit μA Value Provide Feedback Request Answer Units ?
The four pipes below have steady flow of an incompressible, ideal fluid with density ps. The manometer fluid density is pm. Define AP = P2-P₁. Note the manometer reading Rm is called Ah in Figure 2.11 of Song (2018). Part A For each manometer, check the appropriate box in each of the three pairs of options. Rm (a) □ Pm Pr □ P₁ P₂ AP=Rm(Ym-Y) AP=Rm(Yr Ym) (b) □Pm Pr O P₁ P₂ OP₁ > P₂ AP=Rm(Ym-Y) AP=Rm(Yr Ym) Rin (c) □ Pm Pr □ P₁ P₂ DAP-Rm(Ym-Y) AP=Rm(Yr Ym) Rm (d) OPm Pr □ P₁ P₂ *2 O AP=Rm(Ym-Yt) □ AP=Rm(Yt-Ym) Part B For one of the manometers shown, derive the equation you checked for pressure drop AP. Be sure to state which manometer are you using for your derivation (a)-(d).
Water in the reservoir is used to control the water pressure in the pipe at A. Take pHg = 13550 kg/m³ and p = 1000 kg/m³ Neglect the diameter of the pipe. (Eigure 1) Figure AQ B E h 400 mm C 150 mm 100 mm 200 mm Mercury pe he Y Part A If h= 140 mm, determine the gage pressure in the pipe at A when the mercury is at the elevation shown. Express your answer to three significant figures and include the appropriate units. PA 76.8 Submit 4 Provide Feedback kPa CINC Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining
The graphic below shows a reducing section that is part of a vertical pipeline. The pipeline contains an oil (S = 0.8) that is flowing at a rate of 0.6 m³/s. The pressure at the entrance to the reducing section (i.e. the larger diameter section indicated as point 1) is p₁= 200 kPa. The dimensions of the section are: L= 450 mm, D₁= 450 mm and D₂= 300 mm. Assume the temperature as 5°C. Ľ. X P₁ D₂ D₁ Q (2 Determine the force on the reducing section. In your calculations you should neglect losses but include gravity. Draw appropriate diagrams to support your working out. Magnitude of the force: L 1
Answered quickly explanation
please solve in SI units
A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre line of the pipe is so located that the end Bis 2 m above the level of A. Liquid of specific gravity 0.9 flows through the pipe at 150 litres/ second. Pressure gauges connected at A and B show the readings of 60 kPa and 40 kPa, respectively, Determine the direction of flow.
2. Oil of specific gravity of 0.90 is discharging through a 100 mm circular sharp edge orifice in the end of a 120mm pipe. The pressure head on the center line of the pipe just upstream from the orifice is 9m of oil, and discharges takes place into a closed tank in which the vapor pressure is - 20 kPa. Use C = 0.68 and Cv = 0.97. Compute the discharge. 120 mm pipe P = - 20 kPa 100 mm orifice
i)Calculate the flow rate through the system.
With a=4 b=1 c=1
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
a=4 b=0 C=1